mypros+
Error code reference

Dacor Range Error Code F32

Data cable between relay board and control panel loose or defective, defective membrane, or cables to door…

Dacor codesDacor range codes

Data cable between relay board and control panel loose or defective, defective membrane, or cables to door latch loose or defective.

First step from the service manual

Tighten connections, replace if necessary.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F32.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F32 means on a Dacor range

The F32 error code on a Dacor range indicates a communication or connectivity fault involving the data cable between the relay board and the control panel, a defective membrane switch assembly, or a wiring issue with the door latch cables. The relay board serves as the intermediary between the main control panel and the various operational components of the range. When the data cable connecting these two boards becomes loose, corroded, or internally broken, the control panel loses the ability to send and receive proper signals, triggering the F32 fault.

The membrane switch, which is the touch pad interface on the control panel face, can also cause this code if it develops internal failures such as cracked circuits, delamination, or worn contact points. A defective membrane sends erratic or no signals to the control panel, mimicking a communication break. Similarly, the door latch wiring connects the latch mechanism to the relay board, and if those cables become loose at either end or develop a break in the wire insulation, the control system detects an abnormal state and logs F32.

Diagnosing this code begins with physically inspecting and reseating all data cable connectors between the relay board and the control panel, as well as the connectors at the door latch. Connectors should be firmly seated with no corrosion or bent pins. If reseating does not clear the fault, each component including the membrane, data cable, and door latch wiring should be inspected more closely for physical damage and replaced as needed.

Source: manufacturer service documentation.

Common causes of F32

  1. 01

    Loose data cable between relay board and control panel

    Wiring / connection

    The connector linking the relay board to the control panel can work itself loose over time due to vibration or heat cycling. Inspect both ends of the cable for a secure, fully seated connection and reseat if needed.

  2. 02

    Defective membrane switch

    Part replacement

    The membrane touchpad on the control panel face can fail internally due to worn contact points or cracked circuit traces, causing it to send incorrect or no signals. A membrane failure typically requires full replacement of the membrane assembly.

  3. 03

    Loose or broken door latch cables

    Wiring / connection

    The wiring harness connecting the door latch to the relay board can become unseated at its connectors or develop a break in the wire. Inspect the latch wiring at both the latch end and the board connector for looseness or visible damage.

  4. 04

    Corroded or damaged cable connectors

    Part replacement

    Moisture or heat exposure can cause corrosion on the data cable connectors, increasing resistance and disrupting signal transmission. Look for discoloration, oxidation, or bent pins at each connector point.

  5. 05

    Defective relay board

    Part replacement

    If all cables are intact and properly connected and the membrane tests correctly, the relay board itself may have failed and be unable to properly receive or process the data signals. Board replacement would be required in this scenario.

See the test procedure for each cause

Frequently asked questions about F32

What does F32 mean on a Dacor range?
F32 on a Dacor range indicates a fault related to the data cable between the relay board and the control panel, a defective membrane switch, or loose and defective cables connected to the door latch. The range has detected a break or disruption in communication between these components. The first step is to inspect and tighten all relevant cable connections before assuming a part needs to be replaced.
Can I fix the F32 error on my Dacor range myself?
If you are comfortable working inside an appliance and can safely disconnect power at the breaker, you may be able to resolve the fault by reseating the data cable connectors between the relay board and control panel, as well as the door latch wiring. However, if the membrane switch or relay board is defective, those components require replacement, which is typically a job for an experienced technician.
Is it safe to use my Dacor range while the F32 code is showing?
A communication fault like F32 can compromise the range's ability to properly control oven functions and respond to door latch status, which is particularly important for self-clean cycles. It is best to avoid operating the range, especially the oven or self-clean feature, until the fault has been diagnosed and resolved. Continuing to operate the appliance could mask a more serious issue or cause additional component damage.
Will resetting the Dacor range clear the F32 error code?
Cycling power to the range by turning off the circuit breaker for a few minutes may temporarily clear the F32 code, but if the underlying cause such as a loose cable or defective membrane is still present, the code will return. A reset alone is not a fix and should only be used as part of the diagnostic process to confirm whether the fault is persistent.
How much does it cost to repair the F32 error on a Dacor range?
Repair costs vary depending on the root cause. If the issue is simply a loose cable connector, a service call to diagnose and reseat connections may cost in the range of $100 to $200. If a membrane switch or relay board requires replacement, parts and labor combined can range from $200 to $500 or more, depending on part availability and your location.

Related Dacor range codes

All Dacor range codes
View all 23 Dacor range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass