mypros+
Error code reference

Dacor Range Error Code F90

Data cable between relay board and control panel loose or defective, defective membrane, cables to door latch…

Dacor codesDacor range codes

Data cable between relay board and control panel loose or defective, defective membrane, cables to door latch loose or defective, defective door latch assembly, or defective power board.

First step from the service manual

Tighten connections or repair cable.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F90.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F90 means on a Dacor range

The F90 error code on a Dacor range signals a communication or connectivity failure within the appliance's control circuit. Specifically, it points to a breakdown somewhere along the data cable that runs between the relay board and the control panel, a loose or defective connection at the door latch wiring harness, a failed membrane switch assembly, or a defective power board. Because this code spans multiple potential fault points, it is essentially a system-level alert indicating that one or more critical components are not communicating or receiving power as expected.

The relay board serves as the intermediary that routes commands from the control panel to the range's operational components. When the data cable linking these two boards becomes loose, pinched, or develops an internal break, signal transmission fails and the control system flags F90. Similarly, the membrane switch (the touch interface on the control panel) can develop dead zones or internal shorts over time, which disrupts input signals and triggers the same code. Door latch wiring issues are also a documented cause, as the latch assembly connects to the control circuit and an interrupted connection there can produce this fault.

Begin diagnosis by inspecting and reseating all data cable connections between the relay board and the control panel, as well as the wiring harness leading to the door latch assembly. A loose connector is the most common and easiest fix. If connections are secure and the error persists, the membrane switch, door latch assembly, or power board will need to be evaluated and likely replaced.

Source: manufacturer service documentation.

Common causes of F90

  1. 01

    Loose data cable between relay board and control panel

    Wiring / connection

    The ribbon or wire harness connecting the relay board to the control panel can loosen over time from vibration or thermal cycling. Reseating or securing this connection is the first recommended diagnostic step.

  2. 02

    Loose or defective door latch wiring

    Wiring / connection

    The wiring harness running to the door latch assembly can become loose at either the latch end or the board connection. Inspect both ends of the latch wiring for corrosion, damage, or disconnection.

  3. 03

    Defective membrane switch

    Part replacement

    The membrane keypad on the control panel can fail internally, causing erratic or missing input signals that trigger communication errors. If the touchpad feels unresponsive or intermittent, the membrane is a likely culprit.

  4. 04

    Defective door latch assembly

    Part replacement

    If the door latch mechanism itself has failed electrically or mechanically, it can generate a fault signal even when the wiring connections are intact. The latch assembly would need to be tested and replaced if found defective.

  5. 05

    Defective power board

    Part replacement

    A failed power board can disrupt voltage supply and communication across the control circuit, producing the F90 code when other components test normal. This is typically diagnosed after ruling out wiring and component-level faults.

See the test procedure for each cause

Frequently asked questions about F90

What does F90 mean on a Dacor range?
F90 on a Dacor range indicates a problem in the communication or wiring circuit between the relay board, control panel, and door latch assembly. The fault can stem from a loose data cable, a defective membrane switch, faulty door latch wiring, a failed door latch assembly, or a defective power board. The error is the range's way of flagging that a critical connection or component in its control system is not functioning correctly.
Can I fix the F90 error myself?
In some cases, yes. If the cause is simply a loose data cable or a disconnected wiring harness at the door latch, reseating those connections may clear the error without replacing any parts. However, if the membrane switch, door latch assembly, or power board has failed, those components require replacement, and working inside the range's control area involves exposure to high-voltage components, so caution and proper precautions are essential.
Is it safe to use my Dacor range while F90 is displayed?
It is generally not recommended to continue using the range while an F90 error is active. This code can indicate a breakdown in the control communication circuit, which may affect how the range responds to commands or manages functions like the door latch. Continued use before diagnosing and resolving the issue could pose a safety risk or lead to further component damage.
Will resetting the range clear the F90 error code?
A power reset, such as turning off the circuit breaker for a few minutes and restoring power, may temporarily clear the F90 code if the fault is intermittent. However, if an underlying issue exists, such as a loose connector or a failed component, the error will return. A reset alone is not a repair and should be followed by a proper inspection of the wiring and components.
How much does it cost to repair a Dacor range F90 error?
Repair costs vary depending on the root cause. If the fix involves reseating a loose cable, the cost may be limited to a service call fee, typically in the range of $75 to $150. If parts are needed, a membrane switch, door latch assembly, or power board can add $100 to $400 or more in parts costs, plus labor. Getting a diagnostic assessment before authorizing repairs helps avoid unnecessary part replacements.

Related Dacor range codes

All Dacor range codes
View all 23 Dacor range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass