mypros+
Error code reference

Electrolux Dishwasher Error Code LD9:off LD10:on LD11:off

Discharge pump error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the LD9:off LD10:on LD11:off error code actually means

Your Electrolux dishwasher tried to drain the water twice but the internal sensor never confirmed that the water was gone, so it stopped to prevent a potential flood or motor damage. This usually means there is a clog somewhere in the drain system, such as in the filter, pump, or drain hose. Clearing the blockage and restarting the dishwasher will often resolve the issue.

Diagnostic procedure

The full LD9:off LD10:on LD11:off procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Remedy the error (check pump/drain for clogs), then continue the program by pressing the ON/OFF key S0.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock LD9:off LD10:on LD11:off procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of LD9:off LD10:on LD11:off

Ranked by how often they cause this code
  1. 1Clogged drain filter or pump impeller
  2. 2Blocked or kinked drain hose
  3. 3Garbage disposal or sink drain blockage
  4. 4Faulty pressostat (pressure switch)
  5. 5Defective discharge pump motor

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about LD9:off LD10:on LD11:off

What does LD9:off LD10:on LD11:off mean on a Electrolux dishwasher?
This error code indicates a discharge pump error where the pressostat has not returned to its baseline position after two pumping cycles. In practical terms, the dishwasher attempted to drain twice and the pressure sensor never confirmed successful drainage. The machine stops the program to avoid a potential overflow or pump damage. The most common cause is a clog in the filter, pump, or drain hose.
Will resetting the dishwasher clear the LD9:off LD10:on LD11:off error?
Pressing the ON/OFF key (S0) is the designated way to resume the program after addressing the drain issue, but it will not permanently clear the error if the underlying cause is still present. If the drain path is not cleared or the faulty component is not repaired, the dishwasher will generate the error again during the next drain cycle. A reset only allows the program to continue once you have corrected the problem.
How much does it cost to repair the LD9:off LD10:on LD11:off error on an Electrolux dishwasher?
If the cause is simply a clog in the filter or drain hose, the repair can be done at no cost beyond your time. If a component has failed, replacement parts and labor costs will vary: a pressostat typically costs between $20 and $60 for the part, while a drain pump motor can range from $40 to $120 or more. Professional labor charges on top of parts typically add $80 to $200 depending on your location and the technician.
How do I fix the LD9:off LD10:on LD11:off error on my Electrolux dishwasher?
Start by removing and cleaning the drain filter assembly, then inspect the pump impeller area for debris or obstructions. Check the drain hose for kinks or clogs and verify that the sink drain or garbage disposal it connects to is clear. Once the drain path is clear, press the ON/OFF key (S0) to resume the program. If the error returns, the pressostat or drain pump motor may need further testing and possible replacement.
Is it safe to keep using my dishwasher when this error appears?
It is not advisable to continue running the dishwasher while this error is active. The control board halts operation precisely to prevent standing water from overflowing or the drain pump motor from running dry and overheating. Address the drain blockage or component fault before resuming normal use to avoid water damage to the unit or your kitchen.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass