mypros+
Error code reference

Electrolux Oven Error Code EGAt

GAS table for this appliance model not found

Electrolux codesElectrolux oven codes

GAS table for this appliance model not found - stops machine. Software missing.

First step from the service manual

Download latest SW version from AGELUX and upgrade machine.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for EGAt.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What EGAt means on a Electrolux oven

The EGAt error code on an Electrolux oven indicates that the appliance's control software cannot locate the GAS table for the specific model. The GAS table is a critical data set embedded in the appliance firmware that defines combustion parameters, burner timing sequences, gas valve control logic, and safety thresholds specific to that oven model. Without this table, the control board has no reference data to safely operate the gas system, so the machine halts completely to prevent unsafe operation.

This error is fundamentally a software or firmware issue, not a mechanical or component failure. It typically surfaces after a failed firmware update, a corrupted flash memory write, or when replacement control hardware is installed without the correct model-specific software package. In some cases, it can appear if the wrong firmware version is loaded onto the board, causing a model mismatch where the GAS table for the detected hardware configuration is absent from the installed software build.

Because the appliance stops operation entirely when EGAt is triggered, no gas cooking functions will be available until the issue is resolved. The prescribed resolution is to obtain the latest software version through the AGELUX platform and perform a firmware upgrade on the unit. Once the correct software containing the appropriate GAS table is successfully written to the control board, the error should clear and normal operation should resume.

Source: manufacturer service documentation.

Common causes of EGAt

  1. 01

    Failed or incomplete firmware update

    Wiring / connection

    If a previous software update was interrupted or did not complete successfully, the GAS table data may not have been written to the control board. This leaves the firmware in a partial state where model-specific combustion parameters are missing.

  2. 02

    Incorrect firmware version installed

    Wiring / connection

    Loading a firmware build intended for a different model or variant can result in a missing GAS table, since the table in that build does not match the detected hardware configuration. Checking that the installed software version corresponds exactly to the unit's model number is a key diagnostic step.

  3. 03

    Corrupted control board flash memory

    Part replacement

    If the control board's flash memory has degraded or suffered a corruption event, previously stored firmware including the GAS table may become unreadable. A firmware re-flash may resolve this, but persistent corruption can indicate the board itself needs replacement.

  4. 04

    Replacement control board without model software

    Wiring / connection

    When a control board is replaced with a new or refurbished unit, it may not come pre-loaded with the model-specific GAS table. The correct firmware must be loaded via AGELUX before the board will operate properly.

See the test procedure for each cause

Frequently asked questions about EGAt

What does EGAt mean on a Electrolux oven?
EGAt means the oven's control software cannot find the GAS table for this specific model. The GAS table contains the combustion and gas valve control parameters the appliance needs to operate safely. Without it, the oven shuts down completely. The fix requires loading the correct firmware through the AGELUX platform.
Can I fix the EGAt error myself on my Electrolux oven?
Resolving EGAt requires access to the AGELUX service platform to download and install the correct firmware version, which is typically restricted to authorized technicians. Attempting a firmware update without the proper tools and access credentials risks further corrupting the control board software. It is strongly recommended to contact a qualified service technician for this repair.
Is it safe to use my Electrolux oven when the EGAt code is showing?
No. When EGAt is active, the oven stops all machine functions as a built-in safety measure because the gas control parameters are unavailable. The appliance will not allow gas burner operation in this state, so there is no immediate danger from gas, but the oven cannot be used for cooking until the software issue is corrected.
Will resetting my Electrolux oven clear the EGAt error?
A simple power reset will not clear the EGAt error because the underlying cause is missing or corrupted firmware, not a temporary fault condition. The GAS table data must be restored through a proper firmware update using the AGELUX platform. The error will return immediately after any reset if the software is not corrected.
How much does it cost to repair an EGAt error on an Electrolux oven?
If the repair only requires a firmware update, technician labor costs typically range from around 80 to 150 dollars depending on your location and service provider. If the control board has suffered memory corruption and requires replacement, total costs including parts and labor could range from 200 to 500 dollars or more. A technician can determine after inspection whether a software update alone is sufficient.

Related Electrolux oven codes

All Electrolux oven codes
View all 186 Electrolux oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass