mypros+
Error code reference

Electrolux Oven Error Code Urt3

The RTC internal oscillator is malfunctioning

Electrolux codesElectrolux oven codes

The RTC internal oscillator is malfunctioning - stops machine. Clock oscillator failure.

MyPros+ Max

Get the full diagnostic procedure for Urt3.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Urt3 means on a Electrolux oven

The Urt3 error code on an Electrolux oven indicates a failure in the real-time clock (RTC) internal oscillator circuit. The RTC is a dedicated timekeeping component integrated into the oven's control board. Its oscillator generates a precise, stable frequency signal (typically 32.768 kHz in most RTC implementations) that drives the clock functions and coordinates timed operations throughout the appliance. When the oscillator malfunctions or stops producing this signal, the control board detects the anomaly and halts normal oven operation to prevent incorrect timing-dependent functions from executing.

This fault causes the oven to stop functioning entirely, as the control system depends on the RTC for accurate timing of bake cycles, broil cycles, and delayed start operations. The oscillator failure can be caused by a defective RTC crystal, degraded solder joints on the clock circuit, or a failed RTC chip itself. Power surges or voltage irregularities from the supply line can also stress and degrade the oscillator circuit over time, leading to intermittent or permanent failure.

Because the RTC and its oscillator are integrated components on the main control board, this fault typically requires control board-level repair or full board replacement. There is no user-serviceable adjustment for the oscillator circuit. Technicians should first rule out supply voltage irregularities and inspect wiring harness connections to the control board before concluding the board itself has failed.

Source: manufacturer service documentation.

Common causes of Urt3

  1. 01

    Failed RTC oscillator crystal on the control board

    Part replacement

    The crystal component that generates the clock signal can fail due to age or electrical stress, producing no usable frequency output. This is the most direct cause of the Urt3 fault and requires control board repair or replacement.

  2. 02

    Defective or degraded main control board

    Part replacement

    The RTC chip and its supporting circuitry are mounted on the main control board. A failure anywhere in that circuit path, including the RTC chip itself, will trigger this error and halt the oven.

  3. 03

    Power surge or voltage irregularity

    Part replacement

    A voltage spike from the home electrical supply can damage sensitive clock circuitry on the control board. If the fault appeared after a power outage or storm, this is a likely contributing factor.

  4. 04

    Loose or damaged wiring connections to the control board

    Wiring / connection

    Poor harness connections supplying power to the control board can cause erratic behavior in the RTC circuit. Inspect all connectors at the control board for corrosion, loose pins, or heat damage.

See the test procedure for each cause

Frequently asked questions about Urt3

What does Urt3 mean on a Electrolux oven?
The Urt3 code indicates that the real-time clock (RTC) internal oscillator on the oven's control board has malfunctioned or stopped functioning. The RTC oscillator is responsible for generating the timing signal that drives the oven's clock and cycle management functions. When this signal fails, the oven stops operating entirely. This is a control board level fault that typically requires professional diagnosis.
Can I fix the Urt3 error on my Electrolux oven myself?
The oscillator circuit is integrated into the main control board and is not user-serviceable through adjustment or simple part swaps at the consumer level. A technician can confirm whether the board needs replacement or if a loose wiring connection is contributing to the fault. Attempting repairs on the control board without electronics experience is not recommended.
Is it safe to use my Electrolux oven while the Urt3 error is displayed?
No. The Urt3 fault causes the oven to stop machine operation entirely, so the oven will not function normally while this code is active. Do not attempt to bypass the fault. The oven should remain off until the control board issue is diagnosed and resolved by a qualified technician.
Will resetting my Electrolux oven clear the Urt3 error?
A power reset by switching off the circuit breaker for several minutes may temporarily clear the display, but if the RTC oscillator circuit has physically failed, the error will return when the oven powers back on. A reset is worth attempting as an initial step, but a recurring Urt3 code indicates a hardware failure that requires part replacement.
How much does it cost to repair an Electrolux oven showing the Urt3 error?
Repair costs depend on whether the main control board needs to be replaced and the cost of labor in your area. Control board replacements for Electrolux ovens typically range from $150 to $400 or more for parts alone, with additional labor costs on top of that. Getting a diagnostic service call from a certified technician will give you a more accurate estimate before committing to the repair.

Related Electrolux oven codes

All Electrolux oven codes
View all 186 Electrolux oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass