mypros+
Error code reference

Fisher & Paykel Dishwasher Error Code F95

Fan control failure on the wash controller.

Fisher & Paykel codesFisher & Paykel dishwasher codes

Fan control failure on the wash controller.

First step from the service manual

Replace the drying fan and wash controller in the tub faulting.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F95.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F95 means on a Fisher & Paykel dishwasher

The F95 error code on a Fisher & Paykel dishwasher indicates a fan control failure detected by the wash controller. Specifically, the wash controller has lost the ability to properly regulate or communicate with the drying fan circuit. The drying fan is responsible for circulating air during the drying phase of the cycle, and the wash controller monitors its operation continuously. When the controller detects that it cannot send or receive valid signals from the fan, it logs this fault and halts normal operation to prevent further damage.

The fault is tied directly to the interaction between two components: the drying fan assembly and the wash controller board housed in the tub. The wash controller governs fan speed, activation timing, and feedback from the fan motor. A failure in this control loop can stem from a faulty fan motor that draws incorrect current, a wiring harness issue between the fan and the controller, or a failed control board that can no longer drive the fan output circuit correctly.

Because the F95 fault implicates both the drying fan and the wash controller, the recommended diagnostic approach is to replace both components in the affected tub. Attempting to replace only one component without evaluating the other risks leaving a root cause unaddressed. Technicians should inspect wiring connections and harness integrity before committing to part replacement, as a damaged connector or corroded pin can produce identical symptoms.

Source: manufacturer service documentation.

Common causes of F95

  1. 01

    Failed drying fan motor

    Part replacement

    The drying fan motor may have seized, burned out, or developed an open circuit, causing the wash controller to detect a loss of fan feedback or an abnormal load. Testing the fan motor for continuity and proper resistance will help confirm this.

  2. 02

    Faulty wash controller board

    Part replacement

    The wash controller board in the tub may have a failed output driver or relay responsible for powering the drying fan circuit. If the fan tests good independently but the fault persists, the controller board is the likely culprit.

  3. 03

    Damaged or corroded wiring harness

    Wiring / connection

    A broken wire, corroded connector pin, or loose plug between the drying fan and the wash controller can interrupt the control signal or power supply, triggering the F95 fault without either component actually being defective.

  4. 04

    Fan blade obstruction or mechanical seizure

    Wiring / connection

    Debris lodged in the fan housing can prevent the blade from spinning freely, causing the motor to stall and draw excessive current. Inspecting the fan cavity for foreign objects or buildup should be an early visual check.

See the test procedure for each cause

Frequently asked questions about F95

What does F95 mean on a Fisher & Paykel dishwasher?
F95 indicates a fan control failure on the wash controller. The dishwasher's control board in the tub has detected that it cannot properly operate or communicate with the drying fan circuit. This causes the machine to stop normal cycle operation until the fault is resolved.
Can I fix the F95 error myself?
Some homeowners with electrical experience can inspect and reseat wiring connectors or check for obvious obstructions in the fan housing. However, resolving F95 typically requires replacing the drying fan, the wash controller board, or both, which involves disassembly of the tub area and handling electrical components. A qualified appliance technician is recommended for this repair.
Is it safe to keep using the dishwasher with an F95 error?
It is not advisable to continue running the dishwasher while F95 is active. The fault indicates a control failure in the fan circuit, and operating the machine in this state could worsen damage to the wash controller or connected components. The dishwasher should remain out of service until the fault is properly diagnosed and repaired.
How much does it cost to repair an F95 error on a Fisher & Paykel dishwasher?
Repair costs will vary depending on which components need replacement. A drying fan assembly typically runs in the range of $30 to $80 for the part alone, while a wash controller board can cost anywhere from $80 to $200 or more. Adding labor from a technician, total repair costs commonly fall between $150 and $400 depending on your location and the extent of the fault.
Will resetting the dishwasher clear the F95 error code?
A power reset may temporarily clear the F95 code from the display, but if the underlying hardware fault in the fan or wash controller is still present, the error will return during the next cycle. A reset alone is not a fix and should only be used as a first step to confirm whether the fault is intermittent or persistent.

Related Fisher & Paykel dishwasher codes

All Fisher & Paykel dishwasher codes
View all 51 Fisher & Paykel dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass