Skip to main content
Error code reference
Fisher & Paykel Dishwasher Error Codes
52 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
A09Sanitize cycle has not met the required wash temperature to sanitize the dishes.A1Water supply faultA3Tub cannot drainA6No spray arm detectedA7Auto recoveryE1Flood detectedE2Motor fault-motor not rotating, drawing too much current, or not drawing enough current…E3Over temperature fault-water temperature has exceeded safe limits.E4Heater plate fault-element timeout (sub code 01) or dropper resistor open circuit (sub…E5Lid fault-lid not starting (sub code 01), no current (sub code 02), or not stalling (sub…E6Fan fault-under current (sub code 02) or over current (sub code 03).E7Detergent diverter fault-under current (sub code 02) or over current (sub code 03).E8Solenoid fault-under current (sub code 02) or over current (sub code 03) on one or more…E9Microcontroller fault-includes ADC error (sub code 04), PSU overvoltage (sub code 05)…ECCommunications error between the mains filter board and controllers.ErrInter-wash controller communications faultF1The flood switch has been activated, indicating a water leak in the base of the…F2The motor is not rotating, possibly due to foreign matter jamming the motor, motor drive…F21Motor bridge over temperature fault.F24Motor stalled, stopped, or overloaded.F25Motor loss of phase.F3The water temperature is sensed as greater than 80°C, possibly due to element failed on…F30Invalid temperatureF31Over temperature faultF4No temperature increase has been recorded when the element is on, possibly due to element…F5Lid motor current too high during start, indicating lid is jammed up or down.F51Lid motor not turningF52Lid motor undercurrentF54Lid motor not stallingF6Communications baud rate error between micro controllers, possibly due to motor control…F7Communications time-out error indicating the motor control micro has crashed and is not…F70Fill valve high current fault.F71Fill valve low current fault.F8RAM fault in the electronic controller.F82Motor controller ADC check failure.F84Fill valve drive failure on the motor controller.F85Bridge temperature sensor fault on the motor controller.F86Motor bridge failure on the motor controller.F87Motor controller current sense error.F9Power Supply / Controller Fault-the product will disable power supply, log the fault…F95Fan control failure on the wash controller.F97Rinse aid pump control failureFC0Motor controller communications faultFC1Wash controller communications faultFC3Inter-wash controller communications faultFEFlow meter fault-only reported in continuous cycle diagnostic mode when a fault is…FFTop tub not responding.U1Fill faultU2Tub open faultU3Time to fill was too short, indicating water was still in the tub, possibly due to…U4Indicates that the F9 fault on the other tub of a double product means this tub cannot…U6Spray arm may have become dislodged from the rotor, or the water supply pressure to the…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Fisher & Paykel error codes
Common questions
How do I find the error code on my Fisher & Paykel Dishwasher?
Most Fisher & Paykel dishwashers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Fisher & Paykel dishwashers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.