Error code reference

Fisher & Paykel Dryer Error Codes

55 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.

1Communications failure between the sensor module and motor control module.1024 volt supply measurement error 105There is no communication between the control board and user interface (UI communication…11Lid lock open circuit.12Lid lock switching device failure.14Sensor module fault.15Sensor module fault.151Drum failure (alternate display code for E7).157Model not defined (alternate display code for ED).16Airflow restriction (User Warning)2Drum gap cannot be located by the optical sensor on the drum tachometer.20Door actuator stalled.21Door actuator required excess voltage.22Door actuator open circuit.23Door actuator movement was interrupted by low voltage (brown out).233EEPROM read error (LCD models only)-the sensor module has problems reading the EEPROM…24Door actuator movement took too long.28Data retrieval error following loss of power.29Brown-out data retrieval error.3Drum stalled (no mechanical movement or tachometer signal lost).30Lid lock unable to lock 4Invalid option link read-the motor control module heat source option link read is invalid.45Display Module ROM Check Error-on power up, the display has checked its memory against a…6Door jammed 7Motor current excessive.7BDisplay Module RAM Check Error-on power up, the display has checked its memory against a…8Exhaust sensor over temperature-the exhaust sensor measures over temperature (element…9Exhaust sensor under temperature E0No error or all error erase.E1Inlet thermistor short circuit.E2Outlet thermistor short circuit.E3Inlet thermistor open circuit.E4Outlet thermistor open circuit.E5Inlet thermistor signal failure.E6Outlet thermistor signal failure.E7Drum failure.E8Door switch signal fail.E9Sensor rod short circuit.EASensor rod open circuit.EBSensor rod signal is static.ECProgramming end erasure endurance near to the limit (flash memory).EDModel not defined.Err2The float switch or pump has failed in the condensate collection tank.Err3The exhaust NTC thermistor and/or its related circuitry have malfunctioned.Err4The heater and/or its related circuitry have malfunctioned (no change in temperature).Err6The lint filter or condenser has restricted air flow (vent duct is restricted).Err9The heater NTC thermistor and/or its related circuitry have malfunctioned.ErrAThe belt switch is open or disconnected; belt may be broken.F1The flood switch has been activated for more than six seconds.F2The motor has not been sensed rotating.F3The water temperature has been sensed at greater than 85°C (185°F).F4No temperature increase has been sensed for 2 hours while the element is on.F9Electronics failure (EEPROM access error).oPnUser warning indicating door is open or obstructed from closing properly.U1Machine has failed to prime with water within approximately 3 minutes.

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Fisher & Paykel error codes

Common questions

How do I find the error code on my Fisher & Paykel Dryer?

Most Fisher & Paykel dryers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Are these codes specific to my model?

The codes here apply broadly to Fisher & Paykel dryers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.