mypros+
Error code reference

Fisher & Paykel Dryer Error Code Err6

The lint filter or condenser has restricted air flow (vent duct is restricted).

Fisher & Paykel codesFisher & Paykel dryer codes

The lint filter or condenser has restricted air flow (vent duct is restricted).

MyPros+ Max

Get the full diagnostic procedure for Err6.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Err6 means on a Fisher & Paykel dryer

Err6 on a Fisher & Paykel dryer signals that the appliance has detected restricted airflow through the drying system. The dryer monitors airflow as part of its thermal management and drying efficiency controls. When airflow drops below the threshold required for safe and effective operation, the control system throws Err6 and halts the cycle to prevent overheating, component damage, or a potential fire hazard. This is a protective fault, not a component failure in itself.

The two primary restriction points identified by this code are the lint filter and the condenser unit. The lint filter collects fiber debris from every load, and if it is not cleaned regularly, buildup becomes dense enough to significantly reduce airflow. On condenser dryer models, the condenser itself accumulates fine lint and dust over time and requires periodic cleaning separate from the lint filter. Either component, when sufficiently clogged, can trigger Err6.

Beyond the internal filter and condenser, the vent duct pathway on vented models is also a recognized cause. A kinked, crushed, or partially blocked exhaust duct restricts the air the dryer needs to exhaust heat and moisture. Bird nests, accumulated lint inside the duct run, or a duct that is too long or has too many bends can all produce this fault. Addressing Err6 requires systematically inspecting and clearing each of these restriction points before resuming operation.

Source: manufacturer service documentation.

Common causes of Err6

  1. 01

    Clogged lint filter

    Wiring / connection

    The lint filter is the most frequently overlooked maintenance item. Heavy lint buildup on the filter screen blocks airflow enough to trigger Err6, especially if the filter has not been cleaned after recent loads.

  2. 02

    Dirty or blocked condenser

    Wiring / connection

    On condenser dryer models, fine lint accumulates in the condenser unit over time. If the condenser has not been cleaned for an extended period, the restriction can become severe enough to cause this fault.

  3. 03

    Blocked or kinked exhaust duct

    Wiring / connection

    On vented models, a crushed, kinked, or lint-packed exhaust duct will restrict the airflow the dryer needs to operate. Inspect the full length of the duct from the dryer to the exterior vent termination for obstructions or damage.

  4. 04

    Blocked exterior vent termination

    Wiring / connection

    The vent hood or flap on the outside of the home can become blocked by lint accumulation, bird nests, or debris. Even if the duct itself is clear, a blocked termination point will restrict airflow and trigger this error.

  5. 05

    Damaged or collapsed duct

    Part replacement

    Flexible plastic or foil duct can collapse or develop internal damage over time, permanently restricting airflow. If cleaning does not resolve the error, the duct section may need to be replaced with rigid or semi-rigid ducting.

See the test procedure for each cause

Frequently asked questions about Err6

What does Err6 mean on a Fisher & Paykel dryer?
Err6 indicates that the dryer has detected restricted airflow in the drying system. The fault points specifically to a clogged lint filter, a blocked condenser, or a restricted vent duct. The dryer stops the cycle automatically to prevent overheating and potential damage. Clearing the restriction is required before the dryer will operate normally again.
How do I fix Err6 on my Fisher & Paykel dryer?
Start by removing and cleaning the lint filter thoroughly. If your model is a condenser dryer, locate and clean the condenser unit as well, following the access instructions in your user guide. Next, inspect the exhaust duct for kinks, crushing, blockages, or lint accumulation, and check that the exterior vent termination is clear. Once all restriction points are cleared, restart the dryer to confirm the error is resolved.
Is Err6 on a Fisher & Paykel dryer a safety concern?
Yes, restricted airflow is a legitimate safety issue. A dryer that cannot exhaust air properly will overheat internally, which increases the risk of component damage and, in severe cases, fire. The dryer's control system triggers Err6 specifically to stop operation before temperatures reach a dangerous level. Do not attempt to bypass or ignore this fault.
Will resetting the dryer clear Err6?
Resetting the dryer may temporarily clear the fault code, but Err6 will return if the underlying airflow restriction has not been resolved. The error is generated by a physical condition, not a software glitch. You need to clean the lint filter, condenser, and duct before a reset will result in successful dryer operation.
How much does it cost to fix an Err6 error on a Fisher & Paykel dryer?
If the cause is simply a dirty lint filter, condenser, or blocked duct, the repair cost can be very low to nothing, just the time required for cleaning. If the duct needs to be replaced due to collapse or damage, materials typically run in the range of $15 to $60 depending on duct type and length. If a service technician is needed to diagnose or clear the blockage, expect labor costs in the range of $80 to $150 depending on your location and the technician's rates.

Related Fisher & Paykel dryer codes

All Fisher & Paykel dryer codes
View all 54 Fisher & Paykel dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass