mypros+
Error code reference

Fisher & Paykel Dryer Error Code 233

EEPROM read error (LCD models only)

Fisher & Paykel codesFisher & Paykel dryer codes

EEPROM read error (LCD models only) – the sensor module has problems reading the EEPROM data in the display module.

First step from the service manual

Replace the display module.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 233.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 233 means on a Fisher & Paykel dryer

Error code 233 on Fisher & Paykel dryers indicates an EEPROM read error specific to LCD display models. The EEPROM (Electrically Erasable Programmable Read-Only Memory) is a small non-volatile memory chip embedded in the display module that stores critical configuration data, calibration settings, and operational parameters. During normal operation, the sensor module continuously communicates with the display module to read this stored data. When that read operation fails or returns corrupted data, the dryer logs error 233 and may interrupt the current cycle.

The fault is localized to the communication pathway between the sensor module and the display module, or to the display module's EEPROM chip itself. This can result from a failed or degraded EEPROM chip that can no longer reliably hold or transmit its stored data, a corrupted memory state caused by a power surge or voltage irregularity, or a faulty connection between the two modules. Because this error is exclusive to LCD models, it directly involves the LCD display assembly rather than a simpler indicator-based control panel.

The primary recommended diagnostic action is replacement of the display module. This is because the EEPROM is integrated into the display module assembly, making chip-level repair impractical in a field service context. If the error persists after display module replacement, the sensor module itself or the wiring harness connecting the two components should be inspected for damage, corrosion, or loose connectors.

Source: manufacturer service documentation.

Common causes of 233

  1. 01

    Failed display module EEPROM chip

    Part replacement

    The EEPROM chip inside the display module has degraded or failed and can no longer reliably store or transmit data. This is the most common root cause and is resolved by replacing the entire display module.

  2. 02

    Corrupted EEPROM data from power surge

    Part replacement

    A voltage spike or sudden power interruption can corrupt the data stored in the EEPROM, causing read errors. If the dryer experienced a recent power event, this may be the trigger.

  3. 03

    Loose or damaged wiring harness between display and sensor module

    Wiring / connection

    A poor connection or damaged connector on the harness linking the display module to the sensor module can disrupt data communication. Inspect the connector pins for corrosion, bending, or looseness before replacing the display module.

  4. 04

    Faulty sensor module

    Part replacement

    If the display module replacement does not resolve the error, the sensor module that initiates the EEPROM read request may itself be defective. This is a secondary suspect once the display module has been ruled out.

See the test procedure for each cause

Frequently asked questions about 233

What does 233 mean on a Fisher & Paykel dryer?
Error 233 on a Fisher & Paykel dryer indicates an EEPROM read error that occurs only on LCD display models. The sensor module is unable to successfully read data stored in the display module's EEPROM chip. This points to a hardware fault within the display module assembly and typically requires replacing that component.
Can I fix error 233 myself on a Fisher & Paykel dryer?
A knowledgeable DIYer can inspect and reseat the wiring harness connectors between the display module and the sensor module as a first step. However, if the EEPROM chip itself has failed, the display module will need to be replaced, which involves disassembling the control panel area. If you are not comfortable working with appliance electronics, a qualified technician is recommended.
Will resetting my Fisher & Paykel dryer clear error code 233?
A simple power reset is unlikely to permanently clear error 233 if the underlying hardware fault remains. If the EEPROM chip has failed or its data is corrupted, the error will return after power is restored. A reset may temporarily clear the display, but the root cause must be addressed to resolve the fault.
Is it safe to use my Fisher & Paykel dryer when error 233 is showing?
Error 233 indicates a problem with the control display module and its stored settings, which means the dryer may not operate reliably or as intended. Running the dryer with an unresolved control fault is not recommended, as settings and cycle parameters may not be correctly applied. The dryer should be diagnosed and repaired before regular use continues.
How much does it cost to repair error 233 on a Fisher & Paykel dryer?
Repair costs will depend on whether only the display module needs replacement or additional components such as the sensor module are also involved. Parts costs for a replacement display module typically fall in a moderate range, and professional labor adds to the total. Overall, expect repair costs to range from around $150 to $400 or more depending on your location and the specific parts required.

Related Fisher & Paykel dryer codes

All Fisher & Paykel dryer codes
View all 54 Fisher & Paykel dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass