mypros+
Error code reference

Fisher & Paykel Dryer Error Code E0

No error or all error erase.

Fisher & Paykel codesFisher & Paykel dryer codes

No error or all error erase.

MyPros+ Max

Get the full diagnostic procedure for E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E0 means on a Fisher & Paykel dryer

The E0 code on a Fisher & Paykel dryer is a status indicator rather than a fault condition. It signals that no active errors are present in the control system's memory, or that all previously stored error codes have been successfully erased. This code is commonly seen immediately after a diagnostic session is cleared, after a factory reset is performed, or when the technician cycles through the error code display menu and the controller confirms a clean error log.

From a technical standpoint, the dryer's control board continuously monitors connected components and sensors, logging any fault events to non-volatile memory. When a technician or the control system itself clears this memory, the board returns to a baseline state and displays E0 to confirm the log is empty. This is normal behavior and does not indicate any malfunction in the appliance.

If E0 appears during normal operation outside of a diagnostic mode, it simply means the machine is running without any detected faults. No component replacement or repair is needed when this code is displayed. Technicians may encounter it after resolving an actual fault and clearing the error log, confirming that the repair was successful and the board has accepted the reset.

Source: manufacturer service documentation.

Common causes of E0

  1. 01

    Error log cleared after repair

    Wiring / connection

    A technician completed a repair and erased stored fault codes from the control board memory. E0 confirms the log is now empty and no faults remain recorded.

  2. 02

    Diagnostic mode entered with no faults present

    Wiring / connection

    The technician or user accessed the error code display menu on the control panel and the system reported E0 because no fault events are stored in memory.

  3. 03

    Factory or power reset performed

    Wiring / connection

    A manual reset of the control board cleared all stored data, returning the error log to its default empty state and displaying E0 as confirmation.

  4. 04

    Normal operation with no detected faults

    Wiring / connection

    The dryer is functioning correctly and all monitored components are within normal parameters. E0 reflects the absence of any logged fault conditions.

See the test procedure for each cause

Frequently asked questions about E0

What does E0 mean on a Fisher & Paykel dryer?
E0 on a Fisher and Paykel dryer means there are no active errors stored in the control board's memory. It is a status confirmation, not a fault code. The display of E0 indicates either that the machine is operating normally or that all previously logged errors have been erased.
Do I need to fix anything when I see E0 on my Fisher and Paykel dryer?
No repair or action is required when E0 is displayed. The code simply confirms that the control board's error log is empty. If the dryer is running normally and E0 appears, you can continue using the appliance without concern.
Is it safe to use my dryer when E0 is showing?
Yes, E0 indicates the absence of any fault condition, so the dryer is safe to operate. This code does not represent a component failure, overheating issue, or any other safety concern. If the dryer is drying clothes properly, no further action is needed.
Will resetting my Fisher and Paykel dryer clear the E0 code?
E0 does not need to be cleared because it is not a fault. It will naturally disappear once the dryer exits diagnostic mode or resumes normal operation. Performing a reset when E0 is displayed will simply produce the same result, as the error log is already empty.
How much does it cost to fix an E0 error on a Fisher and Paykel dryer?
There is no cost associated with an E0 code because it does not represent a fault or require any repair. If a technician was called to diagnose an issue and cleared a previous fault code, the service call fee would typically fall in the range of $75 to $150 depending on your location, but that cost is for the prior repair work, not for E0 itself.

Related Fisher & Paykel dryer codes

All Fisher & Paykel dryer codes
View all 54 Fisher & Paykel dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass