mypros+
Error code reference

Fisher & Paykel Dryer Error Code 45

Display Module ROM Check Error

Fisher & Paykel codesFisher & Paykel dryer codes

Display Module ROM Check Error – on power up, the display has checked its memory against a known reference and found differences (Intuitive & AeroSmart models).

First step from the service manual

Replace display module.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 45.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 45 means on a Fisher & Paykel dryer

Error code 45 on Fisher & Paykel Intuitive and AeroSmart dryers indicates a Display Module ROM Check Error. This fault is triggered at power-up when the display module performs an internal memory self-test. During this test, the module compares its stored ROM (read-only memory) data against a known reference checksum. If the values do not match, the dryer interprets this as memory corruption or a hardware fault within the display module itself and reports error code 45.

The display module in these Fisher & Paykel dryers handles user interface functions, control signal interpretation, and program logic specific to the front panel. Because the ROM check happens at startup before normal operation begins, error 45 will typically prevent the dryer from running at all. The fault is internal to the display module's memory, meaning external wiring or sensors are generally not the root cause. Corruption can result from a failing internal memory chip, a voltage spike during a previous power cycle, or simple component degradation over time.

Because the fault is confirmed to originate within the display module, the recommended diagnostic action is direct replacement of the display module. There is no field-level repair procedure for reprogramming or reflashing the ROM on these units. Once a new display module is installed and powers up successfully with a passing memory check, the error should not recur. If error 45 persists after replacement, inspect wiring connections between the display module and the main control board for damage or corrosion.

Source: manufacturer service documentation.

Common causes of 45

  1. 01

    Failed Display Module ROM

    Part replacement

    The internal memory chip within the display module has become corrupted or degraded, causing the startup self-test to fail. This is the most common cause and is resolved by replacing the display module.

  2. 02

    Voltage Spike or Power Surge Damage

    Part replacement

    A sudden surge or spike in household power during a previous cycle can corrupt the ROM data stored in the display module. Check for signs of electrical damage on the module's circuit board.

  3. 03

    Component Degradation Over Time

    Part replacement

    Normal aging of the display module's memory components can eventually cause the ROM checksum to fail at startup. This is more likely on older units that have accumulated significant run time.

  4. 04

    Loose or Damaged Wiring to Display Module

    Wiring / connection

    If the wiring harness connecting the display module to the main control board is loose, corroded, or damaged, the module may receive unstable power and fail its memory check. Inspect and reseat all connectors before replacing the module.

See the test procedure for each cause

Frequently asked questions about 45

What does 45 mean on a Fisher & Paykel dryer?
Error code 45 indicates a Display Module ROM Check Error. On Intuitive and AeroSmart models, the display module tests its own internal memory every time the dryer powers up. If that memory test finds differences from the expected reference data, the dryer displays error 45 and will not operate normally.
Can I fix error code 45 myself on a Fisher & Paykel dryer?
The fix for error 45 is replacement of the display module, which is a task many experienced DIYers can perform. Before ordering a new module, check that all wiring connectors to the display are fully seated and free of corrosion. If the wiring is intact, the display module itself will need to be replaced to resolve the fault.
Will resetting my Fisher & Paykel dryer clear error code 45?
A simple reset is unlikely to permanently clear error 45. Because the fault is caused by corrupted or degraded memory inside the display module, the same ROM check will fail again the next time the dryer powers up. The underlying hardware issue must be corrected by replacing the display module.
Is it safe to use my Fisher & Paykel dryer when error 45 is displayed?
Error 45 typically prevents the dryer from completing a normal start, so operating it in its usual cycle is generally not possible while this fault is active. You should not attempt to bypass the error. Have the display module inspected and replaced before returning the dryer to service.
How much does it cost to fix error code 45 on a Fisher & Paykel dryer?
The cost to repair error 45 depends on whether you hire a technician or replace the display module yourself. Parts costs for a replacement display module typically fall in the range of $80 to $200 depending on availability and model. Adding professional labor, total repair costs generally range from $150 to $350.

Related Fisher & Paykel dryer codes

All Fisher & Paykel dryer codes
View all 54 Fisher & Paykel dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass