mypros+
Model reference

Fisher & Paykel DEGX2

Dryer

18 documents25 error codes14 service modes

Available documentation

Tech Sheet

  • DEGX1-DEGX2 Test Page1 pg
    Covers this model

Service Manual

  • Dryer Manual 517760B65 pg
    Covers this model
  • Service Manual smartload™ DRYER65 pg
    Covers this model
  • DRYER65 pg
    Covers this model
  • Gas & Electric Dryers Service Summary5 pg
    Covers this model
  • INTUITIVE & AEROSMART DISPLAY MODULE - Gas & Electric Dryers Service Summary5 pg
    Covers this model

Bulletin

  • No Heat – SmartLoad® and Intuitive® Top Loading Dryers1 pg
    Covers this model
  • Long Drying Times2 pg
    Covers this model
  • New Model Introduction - DEIX2, DGIX2 Dryers Service Bulletin6 pg
    Covers this model
  • New Model Introduction – SmartLoad™ Dryer Refresh & DE09, DG092 pg
    Covers this model
  • New Model Introduction – SmartLoad™Dryer Refresh & DE09, DG092 pg
    Covers this model
  • Service Bulletin13 pg
    Covers this model
  • FPBulletins408 - Washers & Dryers Change in Models and Product Codes / AquaSmart Size Setting12 pg
    Covers this model

Other

  • 395623C4 pg
    Covers this model
  • S FDRT 09 04 Tripping Thermostat4 pg
    Covers this model
  • SFDRT0601Long Drying Times2 pg
    Covers this model

Installation Guide

  • Dryer Installation instructions and User guide108 pg
    Covers this model

Quick Reference

  • Fisher & Paykel Quick Reference Guide 12/1028 pg
    Covers this model
MyPros+ Max

Diagnose your Fisher & Paykel DEGX2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (25)

CodeMeaning
1Communications failure between the sensor module and motor control module.1024 Volt supply measurement error105Communications failure between the sensor module and display module (Intuitive…11Lid lock open circuit.12Lid lock switching device failure.14Sensor module fault.15Sensor module fault.16Airflow restriction2Drum gap cannot be located by the optical sensor on the sensor module.20Door actuator stalled.21Door actuator required excess voltage.22Door actuator open circuit.23Door actuator movement interrupted by low voltage (brown out).24Door actuator movement took too long.28Data retrieval error following loss of power.29Brown-out data retrieval error.3Drum stalled30Lid lock unable to lock4The motor control module heat source option link read is invalid.45Display Module ROM Check Error6Door jammed7Motor current excessive.7BDisplay Module RAM Check Error8Exhaust sensor over temperature (fire detection, element short circuit or low…9Exhaust sensor under temperature (open circuit or not plugged in).

Service modes (14)

  • Conductivity Contact Impedance Check["Enter diagnostic mode (press and hold Auto Dry down button, then press Power button).","Press the…
  • Data Download Mode1
  • Diagnostic Mode1
  • Diagnostic Mode A (AeroSmart LCD)["Ensure power supply to the machine is switched on.","Press and hold the Wrinkle Free button, then…
  • Diagnostic Mode A (AeroSmart LED) – Conductivity Impedance Check["Enter the diagnostic mode (AeroSmart LED).","Press the Time Dry button five times."]
  • Diagnostic Mode A (AeroSmart LED) – Last Fault Option["Press and hold the WRINKLE FREE button (button A) and the POWER button (button B).","The dryer is…
  • Diagnostic Mode A (LED) – Conductivity Impedance Check["Enter diagnostic mode (AeroSmart LED).","Press the Time Dry button five times."]
  • Diagnostic Mode G – Conductivity Impedance Check["Enter diagnostic mode (General).","Press the Auto Dry up button five times."]
  • Diagnostic Mode G (General) – Last Fault Option["Turn the power supply to the dryer on.","Press and hold the Wrinkle Free down button, while…
  • Diagnostic Mode I (Intuitive)["Ensure power supply to the machine is switched on.","Press and hold the Lifecycles button, then…
  • Diagnostic Mode I and A (LCD) – Conductivity Impedance Check["Enter diagnostic mode for Intuitive or AeroSmart LCD.","Navigate to the Machine Status…
  • Last Fault["Enter diagnostic mode (press and hold Auto Dry down button, then press Power button).","Press the…
  • Last Fault Recall1
  • Showroom Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel dryer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax