mypros+
Error code reference

Fisher & Paykel Refrigerator Error Codes

72 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.
0No failure detected; successful Power Up test.1Compressor can't start10Evaporator outlet sensor hot105Communications fault between the cabinet module, the display module/user interface and…11Compartment sensor cold12Compartment sensor hot13The low ambient heater is drawing less current than expected; either the heater or wiring…14The low ambient heater is drawing more current than expected; either there is a short in…15Condenser fan not off16Condenser fan not on17Evaporator fan not off18Evaporator fan not on19Reserved.2Defrost timeout20The flapper heater current is low21The flapper heater current is high22The resistance of the ambient sensor is outside the normal range (> 45K Ohms); sensor cold23The resistance of the ambient sensor is outside the normal range (< 660 Ohms); sensor hot24The resistance of the ice tray sensor is outside the normal range (> 45K Ohms)25The resistance of the ice tray sensor is outside the normal range (< 660 Ohms)26The icemaker motor has timed out; the icemaker gearbox is not returning to the start…27The icemaker motor current is high28The icemaker solenoid is drawing more current than expected; either there is a short in…29The icemaker solenoid is drawing less current than expected; either the wiring is open…3Filter sensor cold30Display harness fault31Display harness fault32Solenoid Driver 1 has failed33Solenoid Driver 2 has failed34Both Solenoid Drivers 1 and 2 have been detected to have a fault.4Filter sensor hot40Icemaker solenoid transistor 1 short circuit; a transistor on the controller that drives…41Icemaker solenoid transistor 2 short circuit.42The icemaker fill tube nozzle heater current is high (only seen with data download using…43The icemaker fill tube nozzle heater current is low / element open circuit (only seen…44The PC return duct heater current is too high (only seen with data download using Smart…45The PC return duct heater current is too low (only seen with data download using Smart…49Communication error between control module and inverter.5Defrost sensor cold6Defrost sensor hot7Evaporator inlet sensor cold8Evaporator inlet sensor hot9Evaporator outlet sensor coldEMB-2Embraco inverterEMB-3Embraco inverterEMB-4Embraco inverterEMB-5Embraco inverterF30No display signal received (shorted or broken wire).F31No display signal received (shorted or broken wire) on clock or data line.F32Solenoid Driver 1 & 2 (transistor) has failed, or the solenoid has failed (display board…F33Solenoid Driver 2 (transistor) has failed (display board fault code).F34Both Solenoid Drivers have failed (display board fault code).F40Icemaker solenoid Transistor 1 Short CircuitF41Icemaker display fault (indicated in fault history on LCD Display).INV-1Inverter module error (LED flashes 1 time on inverter).INV-10Inverter module error (LED flashes 10 times on inverter).INV-11Compressor starts and stops.INV-12Compressor starts and stops.INV-13Over current detected.INV-14Communication error between control module and inverter.INV-15AC input voltage is low.INV-16Inverter module error (LED flashes 16 times on inverter).INV-17Motor bridge temperature above 100°C (212°F).INV-18Inverter PCB over temperature.INV-2Inverter module error (LED flashes 2 times on inverter).INV-3Inverter module error (LED flashes 3 times on inverter).INV-4Inverter module error (LED flashes 4 times on inverter).INV-5Inverter module error (LED flashes 5 times on inverter).INV-6Inverter module error (LED flashes 6 times on inverter).INV-7Inverter module error (LED flashes 7 times on inverter).INV-8Compressor cannot start after 6 attempts.INV-9Inverter module error (LED flashes 9 times on inverter).

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Fisher & Paykel error codes

Common questions

How do I find the error code on my Fisher & Paykel Refrigerator?
Most Fisher & Paykel refrigerators show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Fisher & Paykel refrigerators. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.