mypros+
Error code reference

Fisher & Paykel Refrigerator Error Code 0

No failure detected; successful Power Up test.

Fisher & Paykel codesFisher & Paykel refrigerator codes

No failure detected; successful Power Up test.

MyPros+ Max

Get the full diagnostic procedure for 0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0 means on a Fisher & Paykel refrigerator

Error code 0 on a Fisher & Paykel refrigerator is not a fault condition. It indicates that the control board completed its Power Up self-test sequence successfully and detected no failures in any of the monitored systems. When the refrigerator powers on, the control board runs a diagnostic routine that checks communication between components, sensor readings, and basic electrical integrity. A result of 0 means every check passed within acceptable parameters.

This code may appear briefly in the display or diagnostic readout during startup before the unit transitions to normal operation. It is essentially a confirmation signal, telling the technician or user that the system initialized correctly. Seeing this code during a diagnostic scan or service mode read-out is a positive indicator and does not require any corrective action.

If code 0 is observed after clearing a previous fault code, it confirms the fault has been successfully erased and the board has re-initialized cleanly. Technicians performing a post-repair check may use this code as confirmation that the repair resolved the underlying issue and that no additional faults are currently present in the system.

Source: manufacturer service documentation.

Common causes of 0

  1. 01

    Normal power-up sequence completed

    Wiring / connection

    The refrigerator completed its startup self-test without detecting any faults. This is the expected result after the unit is powered on or restarted.

  2. 02

    Fault code successfully cleared

    Wiring / connection

    A previous error code was cleared by a technician or reset procedure, and the board re-initialized without finding any remaining faults. Code 0 confirms the prior fault is no longer active.

  3. 03

    Post-repair confirmation

    Wiring / connection

    After a component replacement or repair, the control board ran its diagnostic routine and found all systems operating within normal parameters. This is the desired outcome following any service work.

See the test procedure for each cause

Frequently asked questions about 0

What does 0 mean on a Fisher & Paykel refrigerator?
Code 0 means the refrigerator completed its Power Up self-test and found no failures in any monitored system. It is a confirmation code, not a fault. No repair or service action is required when this code is displayed.
Do I need to fix anything when I see code 0 on my Fisher and Paykel refrigerator?
No action is needed. Code 0 indicates that all systems checked out successfully during the startup diagnostic. Your refrigerator is operating normally and no components require attention.
Is it safe to keep using my refrigerator when it shows code 0?
Yes, code 0 is a safe status. It means the control board found no faults or abnormalities during its self-test. Your refrigerator is safe to use and food stored inside is not at risk.
How much does it cost to repair a Fisher and Paykel refrigerator showing code 0?
There is no repair needed for code 0 and therefore no associated cost. If you are seeing this code after clearing a previous fault, the unit has confirmed successful initialization and no further diagnosis is required.
Will resetting my Fisher and Paykel refrigerator clear code 0?
Code 0 is not a fault code that needs to be cleared. It will naturally transition off the display as the refrigerator moves into normal operation after startup. Performing a reset is unnecessary and will simply result in the board running its self-test again, which will again return code 0 if no faults are present.

Related Fisher & Paykel refrigerator codes

All Fisher & Paykel refrigerator codes
View all 71 Fisher & Paykel refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass