mypros+
Error code reference

GE Dryer Error Code 2n

Ultra Care relay turns ON during Field Service Mode test (gas dryer only).

GE codesGE dryer codes

Ultra Care relay turns ON during Field Service Mode test (gas dryer only).

MyPros+ Max

Get the full diagnostic procedure for 2n.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 2n means on a GE dryer

The 2n error code on a GE gas dryer is a diagnostic indicator that appears specifically during Field Service Mode testing. It signals that the Ultra Care relay has activated (turned ON) during this test sequence. The Ultra Care relay is a safety-oriented component in the dryer's control circuit that governs certain operational functions in gas dryer models. When the Field Service Mode test cycles through its relay activation checks, the appearance of the 2n code confirms that this particular relay is responding and energizing as the control board sends the appropriate signal.

This code is not a traditional fault or failure alert in the same sense as most error codes. It is a status indicator generated intentionally during the Field Service Mode diagnostic routine. Technicians use this mode to verify that individual relays and components on the control board are functioning correctly. Seeing 2n during this test means the Ultra Care relay circuit is receiving power and the relay itself is closing, which is the expected behavior during that phase of testing.

If the 2n code appears outside of deliberate Field Service Mode testing, or if the Ultra Care relay appears to be activating unexpectedly during normal operation, this could point to a control board fault, a stuck or shorted relay, or wiring issues within the relay circuit. In those cases, inspection of the control board for signs of heat damage, solder joint failure, or relay component failure would be the appropriate next step. This code applies exclusively to gas dryer models and has no relevance to GE electric dryer diagnostics.

Source: manufacturer service documentation.

Common causes of 2n

  1. 01

    Field Service Mode diagnostic test in progress

    Wiring / connection

    The most common reason for the 2n code is that the dryer is actively running a Field Service Mode test, during which the Ultra Care relay is intentionally triggered. This is expected behavior and not a fault condition.

  2. 02

    Control board relay malfunction

    Part replacement

    If the Ultra Care relay is activating outside of a diagnostic test, the control board may have a faulty relay that is sticking closed or energizing without the correct command. Inspect the board for burn marks, damaged solder joints, or a visibly failed relay component.

  3. 03

    Wiring short in the relay circuit

    Wiring / connection

    A short circuit in the wiring connected to the Ultra Care relay circuit could cause unintended relay activation. Check the wiring harness connected to the control board for damaged insulation, pinched wires, or contact with the dryer cabinet.

  4. 04

    Control board software or reset issue

    Wiring / connection

    In some cases, the control board may retain a test mode state after a Field Service Mode session is interrupted. Power cycling the dryer by unplugging it for several minutes can clear residual test mode conditions.

See the test procedure for each cause

Frequently asked questions about 2n

What does 2n mean on a GE dryer?
The 2n code on a GE gas dryer indicates that the Ultra Care relay turned ON during a Field Service Mode diagnostic test. It is specific to gas dryer models only and is typically a test status indicator rather than a failure alert. If seen during normal operation rather than during a service test, it may point to a control board or wiring issue.
Can I fix the 2n error code on my GE gas dryer myself?
If the code appeared during deliberate Field Service Mode testing, no repair is needed since it is expected behavior. If it appears during normal operation, you can start by power cycling the dryer to clear any residual test mode state. Further diagnosis involving the control board or relay wiring is best handled by a qualified technician, especially on a gas appliance.
Is the 2n error code on a GE gas dryer a safety concern?
The 2n code itself is a diagnostic status indicator and not an immediate safety alarm. However, if the Ultra Care relay is activating unexpectedly outside of Field Service Mode, this could indicate a control board problem that warrants prompt inspection. Because this is a gas dryer, any suspected control or ignition circuit anomaly should be evaluated by a qualified technician before continued use.
Will resetting my GE dryer clear the 2n error code?
Unplugging the dryer for several minutes and restoring power can clear the 2n code if it was left over from an interrupted Field Service Mode session. If the code returns during normal operation after a reset, the underlying cause, such as a control board relay fault or wiring issue, will need to be diagnosed and corrected for the code to stay cleared.
How much does it cost to repair a GE dryer showing the 2n error code?
If no physical repair is needed and the code was simply a result of Field Service Mode testing, there is no parts cost involved. If a control board replacement is required due to a faulty relay, parts and labor costs typically range from $150 to $400 or more depending on the board price and local labor rates. A wiring repair is generally less expensive, often falling in the $75 to $200 range with a service call.

Related GE dryer codes

All GE dryer codes
View all 159 GE dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass