mypros+
Error code reference

GE Washer Error Code 48

Inverter Fault-Inverter board reports a fault.

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 48 error code actually means

Your GE washer is showing an error because the component that controls your motor's speed is detecting a problem with itself or the electrical signals it's receiving. This can cause the washer to stop spinning or fail to complete a cycle. A technician will need to run a specific test and check the wiring connections before determining if a part needs to be replaced.

Diagnostic procedure

The full 48 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Run Service Mode spin test 14 to full completion; check all inverter board harness connections.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 48 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 48

Ranked by how often they cause this code
  1. 1Loose or corroded inverter board harness connections
  2. 2Failed inverter board
  3. 3Drive motor winding failure
  4. 4Chafed or damaged wiring harness
  5. 5Intermittent power supply issue

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 48

What does 48 mean on a GE washer?
Error code 48 on a GE washer indicates an inverter fault, meaning the inverter board has detected and reported a problem with itself or the motor control system. The inverter board controls the speed and torque of the drive motor, so this fault can prevent spin cycles or stop the washer mid-cycle. Diagnosing this code requires running Service Mode spin test 14 and inspecting all harness connections at the inverter board.
Is it safe to use my GE washer when error code 48 appears?
It is not recommended to continue running the washer while error code 48 is active. The inverter board controls the drive motor, and operating the machine with a confirmed inverter fault could cause further damage to the motor or related components. Stop using the washer and complete the diagnostic steps before attempting any additional cycles.
Will resetting my GE washer clear error code 48?
A power reset may temporarily clear the error code, but if the underlying fault in the inverter board or its wiring is still present, the code will return during the next cycle. A reset alone is not a diagnostic step and does not address the root cause. Running Service Mode spin test 14 to full completion is the proper way to determine whether the fault is consistent or intermittent before deciding on a repair.
Can I fix error code 48 on my GE washer myself?
Some cases of error code 48 are caused by loose harness connectors, which a knowledgeable DIYer can reseat after unplugging the washer. However, running the Service Mode spin test 14 requires familiarity with GE service diagnostics, and replacing the inverter board or drive motor involves working near high-voltage components. If you are not comfortable with appliance electrical diagnosis, a qualified technician should handle the repair.
How much does it cost to fix error code 48 on a GE washer?
If the fix is simply reseating a loose harness connector, the repair may cost little to nothing beyond a service call fee, which typically ranges from $75 to $150. If the inverter board needs replacement, parts and labor can range from $200 to $400 depending on the model and local labor rates. Drive motor replacement tends to be at the higher end of the cost range, often between $250 and $450 including labor.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass