Skip to main contentGet Started
Error code reference
GE Washer Error Code 68
Pressure Sensor Out of Range
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
What the 68 error code actually means
Your GE washer is having trouble sensing how much water is in the tub. A small sensor that measures water level is sending a signal that is either too high or too low for the machine to trust. Until this is fixed, the washer may not fill or drain correctly.
Diagnostic procedure
The full 68 procedure
Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.
MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace pressure sensor. Replace IMC board.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 68 procedure $9.95
Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.
Most common causes of 68
Ranked by how often they cause this code
- 1Failed Pressure Sensor
- 2Damaged or Disconnected Pressure Tube
- 3Water or Debris in the Pressure Tube
- 4Faulty IMC Board
- 5Loose or Corroded Wiring Connections
Most DIYers save hundreds by diagnosing before ordering parts.
Get Started
$29/month · Cancel anytime · Or $9.95 3-day pass
Questions people ask about 68
What does 68 mean on a GE washer?
Error code 68 on a GE washer means the pressure sensor is reading a frequency value outside the accepted range of 35 to 47 Hz. The pressure sensor monitors water level in the tub, and when its signal falls outside this window, the washer cannot reliably control filling. The fault points to either the pressure sensor itself or the IMC board that processes its signal.
Will resetting my GE washer clear the 68 error code?
A reset may temporarily clear the displayed code, but it will not fix the underlying hardware fault. If the pressure sensor is out of range or the IMC board has a fault, the error will return as soon as the washer attempts to sense water level again. A reset is useful for confirming whether the fault is intermittent, but a proper repair is required for a lasting fix.
How much does it cost to repair GE washer error code 68?
If only the pressure sensor needs replacement, parts and labor typically fall in the range of $75 to $175 depending on your location and the technician. If the IMC board is also faulty, total repair costs can rise to the range of $200 to $400 or more, since control boards are significantly more expensive than sensors. Getting a diagnostic quote before committing to a board replacement is a good way to confirm the fault before investing in the higher-cost part.
Can I fix error code 68 on my GE washer myself?
A knowledgeable DIYer can start by inspecting the pressure tube for cracks, kinks, or disconnections, which requires no parts and no special tools. If the tube is intact, replacing the pressure sensor is the next step and is a manageable repair for someone comfortable working with appliance wiring. If the error persists after a new sensor, the IMC board will need to be replaced, which is a more involved repair but still achievable with basic appliance repair experience.
Is it safe to use my GE washer when error code 68 is showing?
It is not recommended to continue using the washer while error 68 is active. Because the pressure sensor is not reading correctly, the machine cannot reliably control how much water enters the tub, which creates a risk of overfilling or running cycles without adequate water. Running laundry under these conditions can also stress other components like the pump and motor.
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass