mypros+
Error code reference

GE Washer Error Code D2

No Brake Resistance

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the D2 error code actually means

Your GE washer has detected a problem with the brake system that stops the drum from spinning. Because this is a safety-related issue, the washer has shut itself down and will not run until the problem is fixed. Try unplugging the washer for a minute and plugging it back in, but if the error comes right back, a technician will need to inspect and repair the brake components.

Diagnostic procedure

The full D2 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Power off unit to clear error; if error returns, machine will require service.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock D2 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of D2

Ranked by how often they cause this code
  1. 1Failed Brake Assembly
  2. 2Broken or Disconnected Brake Wiring
  3. 3Corroded or Loose Connector at Control Board
  4. 4Transient Electrical Fault
  5. 5Faulty Control Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about D2

What does D2 mean on a GE washer?
The D2 code on a GE washer means the control system has detected no brake resistance in the brake circuit. This is a critical fault that causes the washer to disable itself immediately and prevent operation until the issue is resolved. The brake is responsible for safely stopping drum rotation, so the machine locks out as a precaution when this circuit appears to have failed.
Is it safe to use my GE washer when the D2 error is showing?
No. The D2 error is classified as a critical fault, and the washer intentionally disables itself when this code is active. Attempting to bypass or override the lockout is not recommended because the brake system is a key safety component that controls drum stopping. The machine should not be operated until the brake circuit fault is diagnosed and repaired.
How much does it cost to repair a GE washer with a D2 error?
Repair costs depend on which component has failed. If the fix involves reseating a connector or addressing a wiring issue, technician labor costs typically range from around $75 to $150. If the brake assembly needs replacement, parts and labor combined can range from $150 to $350 or more depending on the specific model and your location. A control board replacement is generally the most expensive scenario, often ranging from $200 to $450 or higher.
Will resetting the GE washer clear the D2 error code?
Powering off the washer is the recommended first step and may clear the D2 code if the fault was caused by a temporary electrical issue. However, if the code returns after power is restored, a reset alone will not fix the underlying problem. Continued reappearance of the D2 code means a component in the brake circuit needs to be inspected and likely repaired or replaced.
How do I fix the D2 error code on my GE washer?
Start by powering off the unit completely and then powering it back on to see if the code clears. If it returns, the brake assembly, brake circuit wiring, and connector at the control board all need to be inspected for damage, breaks, or corrosion. If the wiring and connectors are intact, the brake assembly itself or the control board may need to be replaced. A qualified appliance technician should perform this diagnosis if you are not comfortable working with internal washer components.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass