mypros+
Error code reference

GE Washer Error Code INCORRECT FILL WATER LEVEL

The fill water level detected is incorrect; the wash cycle stops.

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the INCORRECT FILL WATER LEVEL error code actually means

Your GE washer detected that the water level inside the tub is not what it should be for the selected cycle, so it stopped to avoid a problem. This is usually caused by a sensor or a small hose that monitors water level not working correctly. You may also want to check that the drain hose is installed at the right height, since a low drain hose can cause water to drain out too fast during filling.

Diagnostic procedure

The full INCORRECT FILL WATER LEVEL procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Press START/OFF button to enter Standby mode, then execute a Diagnostic Test to drain the water. Check electrical connection to pressure switch, pressure switch contacts, pressure switch hose, air dome, and drain hose height.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock INCORRECT FILL WATER LEVEL procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of INCORRECT FILL WATER LEVEL

Ranked by how often they cause this code
  1. 1Faulty or disconnected pressure switch hose
  2. 2Defective pressure switch
  3. 3Blocked or waterlogged air dome
  4. 4Poor electrical connection at the pressure switch
  5. 5Incorrect drain hose height

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about INCORRECT FILL WATER LEVEL

What does INCORRECT FILL WATER LEVEL mean on a GE washer?
This error means the washer detected a water level in the tub that does not match what the selected cycle requires. The machine stops the cycle to prevent an improper wash. The fault is rooted in the pressure sensing system, which includes the pressure switch, its connecting hose, and the air dome. Problems in any of these components or their wiring can trigger this code.
Will resetting my GE washer clear the INCORRECT FILL WATER LEVEL error?
Pressing the START/OFF button to enter Standby mode may temporarily clear the error display, but the code will return if the underlying problem is not corrected. Running the built-in Diagnostic Test after pressing START/OFF is recommended to drain the tub and help identify the source of the fault. A reset alone is not a fix.
How much does it cost to repair the INCORRECT FILL WATER LEVEL error on a GE washer?
Repair costs depend on the root cause. If the fix involves re-securing a hose or adjusting the drain hose height, there may be little to no parts cost involved. Replacing a pressure switch typically falls in the range of $20 to $60 for the part, plus labor if a technician is hired. Professional diagnostic and repair service for this type of fault generally runs between $100 and $250 depending on your location and the extent of the work needed.
Can I fix the INCORRECT FILL WATER LEVEL error myself?
Many of the underlying causes can be addressed without professional help. Start by pressing START/OFF to enter Standby mode and running a Diagnostic Test to drain the tub. Then check that the pressure switch hose is firmly connected and free of cracks or kinks, verify the drain hose is mounted at the correct height, and inspect the electrical connector at the pressure switch for loose or corroded terminals. If the pressure switch itself has failed, replacing it requires basic appliance repair skills and the correct replacement part.
Is it safe to keep using my GE washer when this error appears?
No, you should not continue running wash cycles when this error is active. The washer stops the cycle precisely because the water level is outside the expected range, and operating with an incorrect water level can result in poor cleaning performance or potential overflow. Address the cause of the error before resuming normal use.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass