mypros+
Error code reference

Jenn-Air Microwave Error Code F6E3

Mini oven/warm drawer over temperature (not for built-in ovens).

Jenn-Air codesJenn-Air microwave codes

Mini oven/warm drawer over temperature (not for built-in ovens).

First step from the service manual

Turn oven on and visually inspect all elements (convect, bake, broil) to ensure none are operating when they shouldn't be.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F6E3.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F6E3 means on a Jenn-Air microwave

The F6E3 error code on a Jenn-Air microwave indicates that the mini oven or warm drawer component has exceeded its safe operating temperature threshold. This code is specific to combination appliances that include a secondary cooking or warming cavity, and it does not apply to standard built-in oven configurations. The control board monitors temperature continuously through a dedicated thermal sensor or thermostat, and when the detected temperature climbs beyond the programmed limit, the system triggers this fault to prevent damage or a potential safety hazard.

The most direct cause of this fault is one or more heating elements operating when they should not be. This can occur due to a shorted heating element, a failed relay on the control board that is stuck in the closed position, or a malfunctioning temperature sensor that is sending inaccurate readings to the control board. A stuck relay would cause an element to receive power continuously regardless of the control signal, driving temperatures far beyond the setpoint.

Diagnosis should begin by energizing the appliance and visually confirming whether the convection, bake, or broil elements are glowing or cycling when no cooking mode has been selected. An element that is active during standby strongly points to a welded relay on the control board. If all elements appear off and the fault persists, the thermal sensor circuit should be tested for proper resistance values and continuity to rule out a faulty sensor providing a false over-temperature reading.

Source: manufacturer service documentation.

Common causes of F6E3

  1. 01

    Stuck relay on control board

    Part replacement

    A relay on the control board can weld itself in the closed position, causing a heating element to receive continuous power even when no cooking cycle is active. You can identify this by observing a glowing element while the appliance is in standby mode.

  2. 02

    Shorted heating element

    Part replacement

    A bake, broil, or convection element that has developed an internal short can draw power unintentionally and generate excessive heat. Inspect each element visually for burn marks, blistering, or visible breaks and test for continuity to ground.

  3. 03

    Faulty temperature sensor or thermostat

    Part replacement

    If the thermal sensor in the mini oven or warm drawer cavity is sending incorrect readings to the control board, the board may log an over-temperature condition even when actual temperatures are normal. Testing the sensor's resistance against specifications can confirm whether it is within range.

  4. 04

    Blocked or restricted ventilation

    Wiring / connection

    If the ventilation pathways around the mini oven or warm drawer are obstructed by debris or improper installation clearances, heat can accumulate and trigger the over-temperature fault. Check that all vents are clear and that the appliance has the required clearance on all sides.

  5. 05

    Control board failure

    Part replacement

    Beyond a single stuck relay, broader control board failure can result in incorrect signals being sent to heating circuits, causing uncontrolled element operation. This is typically diagnosed after ruling out individual element and sensor faults.

See the test procedure for each cause

Frequently asked questions about F6E3

What does F6E3 mean on a Jenn-Air microwave?
The F6E3 code means the mini oven or warm drawer section of your Jenn-Air combination appliance has detected an over-temperature condition. The control board monitors the cavity temperature and triggers this fault when the temperature exceeds a safe limit. This code does not apply to standard built-in oven configurations. The appliance should be inspected before resuming use.
Can I fix the F6E3 error myself?
Some steps, such as clearing ventilation obstructions and performing a visual inspection of the heating elements, can be done without specialized tools. However, if a stuck relay or shorted element is the cause, replacing a control board or heating element involves working with high-voltage components and is best handled by a qualified technician. Testing the temperature sensor also requires a multimeter and basic knowledge of resistance testing.
Is it safe to keep using my appliance while the F6E3 code is active?
No, you should not continue using the appliance while this fault is active. The F6E3 code indicates a potential uncontrolled heat condition, which poses a fire risk and could cause damage to the appliance. Disconnect power until the root cause has been identified and resolved.
Will resetting the appliance clear the F6E3 error?
A power reset by disconnecting the appliance for a few minutes may temporarily clear the fault display, but it will not fix the underlying problem. If a relay is stuck, an element is shorted, or the sensor is faulty, the code will return once the appliance is powered back on and the condition is detected again. A reset is only useful as part of initial diagnosis, not as a repair.
How much does it cost to repair the F6E3 error on a Jenn-Air appliance?
Repair costs vary depending on which component is at fault. A replacement temperature sensor is generally the least expensive fix, typically in the range of $20 to $80 for the part. A control board replacement is more costly, with parts commonly ranging from $150 to $400 or more, plus labor if a technician is involved. A heating element replacement typically falls somewhere in between those two ranges.

Related Jenn-Air microwave codes

All Jenn-Air microwave codes
View all 31 Jenn-Air microwave codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass