mypros+
Error code reference

Kenmore Range Error Code 36

Communication error in the Induction Housing Assembly, left side cooking zones.

Kenmore codesKenmore range codes

Communication error in the Induction Housing Assembly, left side cooking zones.

First step from the service manual

Verify communication harness between ESEC-UIB P9 connector and Large Filter Circuit Board X14/X20 connectors.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 36.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 36 means on a Kenmore range

Error code 36 on a Kenmore induction range indicates a communication failure within the Induction Housing Assembly on the left side of the cooktop. Specifically, the control system has lost reliable data communication between the ESEC-UIB (Electronic System and Energy Controller User Interface Board) and the Large Filter Circuit Board, which manages power filtering and signal routing for the left-side induction cooking zones. This communication link runs through the P9 connector on the ESEC-UIB and the X14 and X20 connectors on the Large Filter Circuit Board.

The communication harness carrying signals between these two boards is the first component to inspect. A loose, corroded, or damaged connector at any of the three points (P9, X14, or X20) can interrupt the data signal and trigger this error. Heat cycling, vibration, and grease contamination are common environmental factors that degrade connector integrity over time. The wiring harness itself can also develop internal breaks or shorts from repeated thermal expansion and contraction.

If the harness and connectors check out physically and electrically, the fault may lie within one of the boards themselves. A failed ESEC-UIB or a damaged Large Filter Circuit Board can both generate this code when their communication circuits malfunction. Diagnosing board-level faults typically requires confirming that harness continuity is intact before condemning either board, since board replacements represent a significantly higher cost and complexity than connector or harness repairs.

Source: manufacturer service documentation.

Common causes of 36

  1. 01

    Loose or disconnected harness connector

    Wiring / connection

    The communication harness connectors at ESEC-UIB P9, Large Filter Circuit Board X14, or X20 may have worked loose due to vibration or heat cycling. Reseating each connector firmly is the first corrective step.

  2. 02

    Corroded or contaminated connector pins

    Wiring / connection

    Grease vapor and moisture can cause oxidation or contamination on the connector pins at P9, X14, or X20, increasing resistance and breaking the communication signal. Inspect pins visually and clean with electrical contact cleaner if corrosion is present.

  3. 03

    Damaged communication harness

    Part replacement

    The wiring harness between the ESEC-UIB and the Large Filter Circuit Board can develop internal wire breaks, fraying, or shorts from repeated heat exposure and flexing. A continuity test across each harness wire will confirm whether the cable needs replacement.

  4. 04

    Failed Large Filter Circuit Board

    Part replacement

    If the harness and connectors are intact, the Large Filter Circuit Board itself may have a failed communication circuit at the X14 or X20 connection points. Board-level damage from overvoltage or heat can disrupt signal transmission.

  5. 05

    Failed ESEC-UIB

    Part replacement

    A defective ESEC-UIB can fail to send or receive communication signals through the P9 connector, producing error code 36. This is typically diagnosed only after the harness and Large Filter Circuit Board have been ruled out.

See the test procedure for each cause

Frequently asked questions about 36

What does 36 mean on a Kenmore range?
Error code 36 on a Kenmore induction range signals a communication failure between the ESEC-UIB and the Large Filter Circuit Board for the left-side cooking zones. The control system cannot exchange data between these two components, which prevents normal operation of the left induction burners. The fault is typically found in the wiring harness or connectors linking these two boards.
Can I fix error code 36 on my Kenmore range myself?
If you are comfortable working with appliance electronics, you can start by unplugging the range and inspecting the communication harness connectors at the ESEC-UIB P9 port and the Large Filter Circuit Board X14 and X20 ports for looseness or corrosion. Reseating or cleaning the connectors may resolve the error at no parts cost. However, if the harness or a circuit board needs replacement, most homeowners will benefit from having a qualified appliance technician perform that work.
Is it safe to use my Kenmore range while error code 36 is displayed?
Error code 36 specifically affects the left-side induction cooking zones due to a communication failure. The left burners may be non-functional or behave unpredictably while this fault is active. It is best to avoid using the left cooking zones until the fault is diagnosed and repaired to prevent potential safety issues.
How much does it cost to repair error code 36 on a Kenmore range?
Repair costs vary depending on the root cause. If the fix is simply reseating a connector, labor may be the only expense, typically ranging from $75 to $150 for a service call. If a harness replacement is needed, parts and labor combined could run $100 to $250. Replacing the Large Filter Circuit Board or ESEC-UIB involves higher parts costs, and total repair expenses in those cases can range from $200 to $500 or more depending on parts pricing and labor rates.
Will resetting my Kenmore range clear error code 36?
Unplugging the range for a few minutes and restoring power may temporarily clear the error display, but if the underlying communication fault in the harness or circuit boards is still present, the code will return. A reset alone is not a repair and should only be used as a diagnostic step to confirm whether the fault is persistent or intermittent. Persistent return of code 36 means the physical cause must be identified and corrected.

Related Kenmore range codes

All Kenmore range codes
View all 159 Kenmore range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass