Model reference
Kenmore 790
Range
55 documents101 error codes29 service modes
Available documentation
Service Manual
- ELECTRIC SELF-CLEANING RANGE Use & Care Guide40 pg
- Tabla de materias - Guía de uso y cuidado de estufa30 pg
- Use & Care Guide - Kenmore Elite Dual Fuel Range42 pg
- ELECTRIC BUILT-IN OVEN Use & Care Guide34 pg
- Gas Range Use & Care Guide16 pg
- Galaxy Electric Range Use & Care Guide14 pg
- SERVICE DATA SHEET - Electric Ranges with ES 510/515 Electronic Oven Controls2 pg
- Gas Range Use & Care Guide44 pg
- Gas Range Use & Care Guide42 pg
- ELECTRIC RANGE Use & Care Guide18 pg
- Electric COOKTOP Use & Care Guide14 pg
- ELECTRIC BUILT-IN OVEN Use & Care Guide36 pg
- ELECTRIC BUILT-IN OVEN Use & Care Guide26 pg
- GAS COOKTOP Use & Care Guide17 pg
- Service Data Sheet16 pg
- Electric Range Use & Care Guide14 pg
- SERVICE DATA SHEET - Electric Wall Oven with Electronic Oven Control16 pg
- Electric Range Use & Care Guide26 pg
- Gas Range Use & Care Guide18 pg
- Estufa a Gas - Free-Standing Range17 pg
- Gas Range Use & Care Guide28 pg
- Gas Range Use & Care Guide14 pg
Tech Sheet
- Electric Double Wall Ovens with Electronic Oven Control - Service Data Sheet20 pg
- SERVICE DATA SHEET - Appliance with Electronic Oven Control12 pg
- SERVICE DATA SHEET - Resistance Temperature Detector (RTD) - Electric Range with ES 585 Electronic Oven Control & Pan Sensing4 pg
- Electronic Oven Control (Rear View) Service Data Sheet - Electric Ranges with ES 200/205/300 & 305 Electronic Oven Controls2 pg
- SERVICE DATA SHEET - Gas Ranges with ES 565 Electronic Oven Control2 pg
- SERVICE DATA SHEET - Electric Ranges with ES 200/205/300 & 305 Electronic Oven Controls2 pg
- Electronic Oven Control (E.O.C. - Rear View) Service Data Sheet Dual Fuel Ranges with ES 565 Electronic Oven Control2 pg
- Electric Wall Oven with ES575A Electronic Oven Control Service Data Sheet24 pg
- SERVICE DATA SHEET - Kenmore Frigidaire Range 790 46722700 Tech Sheet20 pg
- Electric Wall Oven with Electronic Oven Control - SERVICE DATA SHEET20 pg
- SERVICE DATA SHEET - Electric Wall Ovens with ES575 Electronic Oven Control20 pg
- SERVICE DATA SHEET - Appliance with Electronic Oven Control20 pg
- SERVICE DATA SHEET 318047307 Electric Double Wall Ovens with Electronic Oven Control20 pg
- Electric Slide-in Range with Electronic Oven Control / Dual Fuel Slide-in Range with Electronic Oven Control / Gas Slide-in Range with Electronic Oven Control16 pg
- SERVICE DATA SHEET - Electric Double Wall Ovens with Electronic Oven Control16 pg
- SERVICE DATA SHEET - Electric Slide-In with ES575 Electronic Oven Control12 pg
- Electronic Oven Control (EOC rear view) SERVICE DATA SHEET Electric Ranges with ES 515 Electronic Oven Controls2 pg
- SERVICE DATA SHEET - Electronic Oven Control (E.O.C. - Rear View)2 pg
- Frigidaire Range 790 31032802 Tech Data Sheet16 pg
- Kenmore Frigidaire Range 790 78503013 Tech Sheet 3169040162 pg
- SERVICE DATA SHEET - Electric Slide-in Range with Electronic Oven Control, Electric Drop-in Range with Electronic Oven Control, Gas Slide-in Range with Electronic Oven Control8 pg
- Kemore Frigidaire Range 790 72851301 Tech Data Sheet 316218504en2 pg
Wiring Diagram
- Kenmore Frigidaire Range Wiring Diagram1 pg
- Frigidaire Oven Wiring sheet1 pg
- Kenmore Frigidaire Range 790 45599900 Wiring Diagram2 pg
- Kenmore Frigidaire Cooktop 790 32443800 Wiring Sheet 3180471111 pg
Other
- ELECTRIC RANGE Slide-in models Use & Care Guide80 pg
Installation Guide
- Electric Range Use & Care Guide36 pg
- Gas Range Use & Care Guide22 pg
- GAS COOKTOP Use & Care Guide16 pg
- Use & Care Guide / Guía de uso y cuidada14 pg
- Use & Care Guide80 pg
- Electric Range Use & Care Guide16 pg
MyPros+ Max
Diagnose your Kenmore 790.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (101)
CodeMeaning
-dr-The oven door was left open while controls were set for the self-cleaning cycle.11Jammed key detected on the ESEC touch panel.14Touch Panel tail missing from the ESEC user interface board.15ESEC self test failure.21LIN (Local Interconnect Network) error30AC input voltage too high at the Induction Housing Assembly (left side cooking…31Internal generator error (sync) in the Induction Housing Assembly, left side…32Power supply defect in the Induction Housing Assembly, left side cooking zones.33Power supply defect in the Induction Housing Assembly, left side cooking zones.34Internal generator error (communication) in the Induction Housing Assembly…35AC input voltage too low at the Induction Housing Assembly (left side cooking…36Communication error in the Induction Housing Assembly, left side cooking zones.37Heat sink temperature sensor break in the Induction Housing Assembly, left side…39Configuration mismatch between the User Interface and the Induction Housing…51Inductor temperature sensor break on the left front (LF) cooking zone.52Inductor temperature sensor break on the left rear (LR) cooking zone.54Inductor temperature sensor break on the right rear (RR) cooking zone.55Inductor temperature sensor break on the right front (RF) cooking zone.61Left front (LF) inductor temperature sensor too hot.62Left rear (LR) inductor temperature sensor too hot.64Right rear (RR) inductor temperature sensor too hot.65Right front (RF) inductor temperature sensor too hot.70AC input voltage too high at the Induction Housing Assembly (right side cooking…71Internal generator error (sync) in the Induction Housing Assembly, right side…72Power supply defect in the Induction Housing Assembly, right side cooking zones.73Power supply defect in the Induction Housing Assembly, right side cooking zones.74Internal generator error (communication) in the Induction Housing Assembly…75AC input voltage too low at the Induction Housing Assembly (right side cooking…76Communication error in the Induction Housing Assembly, right side cooking zones.77Heat sink temperature sensor break in the Induction Housing Assembly, right…View all 101 error codes
CFConv Convert reminder to check foodCLnFlex Clean (self-clean) cycle is actively running.d-OThe oven door was left open while controls were set for the self-cleaning cycle.door LocThe motor driven door latch mechanism is actively locking or unlocking the oven…door OPnOven has cooled sufficiently after self-clean and the door may now be opened.drThe oven door was left open while controls were set for the self-cleaning cycle.E0 11UIB-Shorted keypad problem.E0 13EEPROM Failure on ESEC system.E0 14UIB-TSEC Display Cable problem.E0 15FMEA (Failure Mode Effects Analysis)E0 20Communication break between ES500 and UIB.E0 21Communication break between UIB and Pan Sense Board.E11Shorted keypad on ESEC surface element control.E13Bad EEPROM on ESEC UIB.E14TST/Display tail missingE15ESEC self test failed.E20Loss of LIN communication between ESEC UIB and EOC.E21Loss of communication between UIB and pan sensing PCB.E41Hall effect sensor error (cooling fan failure).E60Ambient oven temperature error for ESEC 20 UIB.E61Ambient oven temperature error for the pan sensing PCB.ENDProgrammed cook time has completed and the oven has shut off automatically.FOven control has detected a fault or error condition (displayed as F followed…F1Electronic control has detected a fault condition.F10Control has sensed a potential runaway oven condition; control may have a…F11Shorted key detectedF12Bad Micro Identification.F13Control's internal checksum may have become corrupted.F14Misconnected keyboard cable.F15Controller self check failed.F16EOC internal software error or failure.F17EOC internal software error or failure.F18EOC internal software error or failure.F2Control has detected a problem with the communications link with the electronic…F20Control has detected a problem with the communication link with the ESEC (some…F21Communication problem between the User Interface Board and the Appliance…F23Control has detected a problem with the communication link with the variable…F24Communication failure between VSC board and EOC (lower oven if so equipped).F26Communication failure with Mini Oven Control Board (models equipped with…F3Electronic control has detected a fault condition.F30Open RTD sensor probe or wiring problemF31Shorted RTD sensor probe or wiring problemF32Key loop is detected as an open circuit.F40Cooktop lockout failure (some models).F43The microwave external cooling fan speed (as read by the tachometer input of…F44The microwave external cooling fan speed (as read by the tachometer input of…F500Loss of LIN Buss communication between EOC and ESEC.F60Electronic Oven Control (EOC) over temperatureF62Improper or corrupt signal voltage between the EOC and power supply board…F700Loss of Display tail #0.F701Loss of Keyboard Tail.F702Shorted Keypad on ESEC.F710Loss of Display tail #1.F80Communication problem between the User Interface Board and the Microwave…F81Damper ErrorF82Microwave thermistor open errorF83Fire detected in microwave ovenF84Communication problem between the User Interface Board and the Microwave…F9Control has detected a problem with the Motor Door Latch Assembly.F90Door motor mechanism failure.F91Maximum oven door unlock attempts exceeded.F92Maximum oven door open time exceeded.F93Maximum oven door lock time exceeded.F94Maximum oven door lock attempts exceeded.F95Door lock motor or latch circuit failure.HotOven is still too hot to open the door after a self-clean cycle has finished.LinE ERREOC internal voltage test error or failure.LocOven door is locked and oven control keypads are locked out.PFPower failure detected; the display flashes PF when the oven is first plugged…SDAppliance set for Display Mode (store demo mode).SFSabbath failure
Service modes (29)
- 12 Hour / 24 Hour Clock Toggle["Press and hold CLOCK SET pad for 7 seconds until 12h or 24h appears in the display","Press CLOCK…
- 12 or 24 Hour Time Display Toggle["Press and hold the Clock Set pad for 7 seconds.","'12Hr' or '24Hr' will appear in the display and…
- Clock Format Change (12h/24h)["1
- Continuous Bake / 12 Hour Energy Saving Toggle["Press and hold Timer Set/Off for 7 seconds until tone is heard.","Within 5 seconds, press UP or…
- ESEC Configuration Reset (Error 39 resolution)1
- Exit Store Display Mode (SD)1
- Factory Reset (Clear All Recipes and Settings)["1
- Factory Reset (Erase All Stored Recipes)["Press and hold BAKE pad until the first single beep sounds (approximately 6 seconds)","After the…
- Factory Test Mode / Potentiometer Calibration Mode["Turn off power to the appliance.","Place all knobs to the OFF or 12:00 position.","Turn power on…
- Fahrenheit / Celsius Toggle["Press and hold BROIL and FLEX CLEAN pads for 7 seconds","550° will first appear then F or C will…
- Meat Probe Cancel Cook Configuration["1
- Meat Probe Reaction Mode (P CC / PnCC)["Before starting cooking, press and hold MEAT PROBE pad for 7 seconds","Use key to toggle to P CC…
- Oven Calibration / Temperature Adjustment["Set EOC to bake at 550°F.","Within 5 seconds of setting 550°F, press and hold the bake keypad for…
- Oven Calibration Adjustment["Set EOC to bake at 550°F.","Within 5 seconds of setting 550°F, press and hold the bake pad for…
- Oven Lock Mode["1
- Oven Lockout["Press STOP/Clear and hold for 3 seconds.","'Door Locked' indicator light will glow and motor…
- Oven Temperature Adjustment["Press and hold BAKE pad for 6 seconds until display shows current offset","Use number pads to…
- Oven temperature calibrationPress and hold the upper or lower oven BAKE pad for 6 seconds on the cavity which needs adjustment
- Oven temperature calibration adjustment1
- Pan Sensing System Calibration1. Remove all cookware and objects from the cooktop surface. 2. Cycle power. 3. Within 300 seconds…
- Sabbath Feature["Set clock to correct time of day.","Press Bake and set desired temperature using UP/DOWN…
- Sabbath Mode["1
- Silent Control Operation["Press and hold DELAY TIME and FLEX CLEAN pads for 7 seconds","Press FLEX CLEAN to switch between…
- Silent control panel modePush and hold the TIMER pad for 7 seconds until the control beeps once.
- Silent Operation Mode["1
- Temperature Calibration Adjustment["Ensure oven is in a non-cooking mode.","Press and hold the BAKE pad for 6 seconds.","The current…
- Temperature conversion (Fahrenheit to Celsius)1
- Temperature Conversion (Fahrenheit/Celsius)["Press and hold Broil for 7 seconds until °F or °C appears in the display.","Press the UP or DOWN…
- Temperature Format Change (Fahrenheit/Celsius)["1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Kenmore range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax