Skip to main content
Error code reference
Kenmore Range Error Codes
160 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
- -Lockout indicator-the electronic surface element control or oven is in locked mode…-- (double dash)ESEC Lockout condition is active; cooktop controls are locked out due to Cooktop Lockout…-- (ESEC)ESEC Lockout condition displayed in the cooktop digital display windows, indicating the…11Jammed key detected on the ESEC touch panel.14Touch Panel tail missing from the ESEC user interface board.15ESEC self test failure.1c1cKey press error-control disables buzzer for the affected key press.1c2cIncorrect keyboard loop value-control disables all outputs and deactivates lighting and…1c31Incorrect key value cancellation (upper cavity)-disables all outputs for cavity 1.1c32Incorrect key value cancellation (lower cavity)-disables all outputs for cavity 1.1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cCalibration value out of limits-'CAL' displayed in time digits.1c8cIncorrect cyclic redundancy check (CRC)-control disables all outputs.1d11Upper oven temperature sensor resistance too high (>2237 ohms at door unlock)-disables…1d12Lower oven temperature sensor resistance too high (>2237 ohms at door unlock)-disables…1d21Upper oven temperature sensor resistance too high (>2787 ohms at door lock)-disables all…1d22Lower oven temperature sensor resistance too high (>2787 ohms at door lock)-disables all…21LIN (Local Interconnect Network) error30AC input voltage too high at the Induction Housing Assembly (left side cooking zones).31Internal generator error (sync) in the Induction Housing Assembly, left side cooking…32Power supply defect in the Induction Housing Assembly, left side cooking zones.33Power supply defect in the Induction Housing Assembly, left side cooking zones.34Internal generator error (communication) in the Induction Housing Assembly, left side…35AC input voltage too low at the Induction Housing Assembly (left side cooking zones).36Communication error in the Induction Housing Assembly, left side cooking zones.37Heat sink temperature sensor break in the Induction Housing Assembly, left side cooking…39Configuration mismatch between the User Interface and the Induction Housing Assembly…3d11Upper oven sensor resistance too high (>3680 ohms)-open sensor circuit; disables all…3d12Lower oven sensor resistance too high (>3680 ohms)-open sensor circuit; disables all…3d21Upper oven sensor resistance too low (<15 ohms)-shorted sensor; disables all cooking…3d22Lower oven sensor resistance too low (<15 ohms)-shorted sensor; disables all cooking…4d11Upper oven door switch not closed when door is locked-disables cleaning and locking…4d12Lower oven door switch not closed when door is locked-disables cleaning and locking…4d51Upper oven door switch is neither open nor closed-disables convection, cleaning and…4d52Lower oven door switch is neither open nor closed-disables convection, cleaning and…51Inductor temperature sensor break on the left front (LF) cooking zone.52Inductor temperature sensor break on the left rear (LR) cooking zone.54Inductor temperature sensor break on the right rear (RR) cooking zone.55Inductor temperature sensor break on the right front (RF) cooking zone.61Left front (LF) inductor temperature sensor too hot.62Left rear (LR) inductor temperature sensor too hot.64Right rear (RR) inductor temperature sensor too hot.65Right front (RF) inductor temperature sensor too hot.70AC input voltage too high at the Induction Housing Assembly (right side cooking zones).71Internal generator error (sync) in the Induction Housing Assembly, right side cooking…72Power supply defect in the Induction Housing Assembly, right side cooking zones.73Power supply defect in the Induction Housing Assembly, right side cooking zones.74Internal generator error (communication) in the Induction Housing Assembly, right side…75AC input voltage too low at the Induction Housing Assembly (right side cooking zones).76Communication error in the Induction Housing Assembly, right side cooking zones.77Heat sink temperature sensor break in the Induction Housing Assembly, right side cooking…9d11Upper oven lock switch not closed (lock position not confirmed)-disables cleaning and…9d12Lower oven lock switch not closed (lock position not confirmed)-disables cleaning and…9d21Upper oven unlock switch not closed (unlock position not confirmed)-disables cleaning and…9d22Lower oven unlock switch not closed (unlock position not confirmed)-disables cleaning and…9d31Latch state unknown in upper oven; both locked and unlocked switches reading closed…9d32Latch state unknown in lower oven; both locked and unlocked switches reading closed…CFCheck Food reminderCLnClean cycle activeCLOCooktop lockout is active; surface element controls are locked.d-0Oven door was opened during the Steam Clean cycle.d-OThe oven door was left open while the control is set for a function requiring a closed…door LocThe motorized door lock mechanism is actively locking or unlocking the oven doordoor OPnOven door is ready to be opened after self-clean cycle cooling period is complete.drOven door is open when setting Self-Clean cycle; oven control continuously beeps…EOven control has detected a fault or error condition (any E code displayed on oven…E XXError code displayed in Cooking Elements LEDs and digits in Main Control LED together…E0 11UIB-Shorted keypad problem.E0 13EEPROM Failure on ESEC system.E0 14UIB-TSEC Display Cable problem.E0 15FMEA (Failure Mode Effects Analysis)E0 20Communication break between ES500 and UIB.E0 21Communication break between UIB and Pan Sense Board.E11Electronic controls have detected a fault condition; error code in the range E11 to E77…E11-E77The oven control has detected an error condition (error codes ranging from E11 to E77).E22Cooktop control has detected a fault condition related to one of the cooking zone pairs.E33Cooktop control has detected a fault condition related to one of the cooking zone pairs.E44Cooktop control has detected a fault condition related to one of the cooking zone pairs.E55Cooktop control has detected a fault condition related to one of the cooking zone pairs.E66Cooktop control has detected a fault condition related to one of the cooking zone pairs.E77Cooktop control has detected a fault condition in one of the cooking zone pairs (upper…ENDA timed function (timer, cook time, or self-clean) has completedErESEC surface element control error displayed (blinking) when power is connected or…ERRAn error code displayed when trying to change the function knob to another function…FThe ESEC control monitors internal and additional circuits; if any system fails, the ESEC…F0-E0No failureF1Electronic oven control (EOC) has detected an internal malfunction, which may include a…F1 E2Internal error.F1 E4Internal error.F1 E5Internal error.F1 E6Internal error.F1 E7Internal error.F1 E8Internal error.F1 E9Internal error.F1-E0EEPROM communications failureF1-E1EEPROM CHECKSUM failureF1-E3Fuel type (gas/electric) select failureF10Electronic oven control has detected a fault condition (example code referenced in…F11Electronic oven control has detected a fault condition (example code referenced in…F12EOC internal software error or failure.F13Control's internal checksum may have become corrupted (EOC).F14Display tail (ribbon connector) missing or not connected.F15Controller self check failed (EOC).F16Potentiometer failure.F2Control has detected a problem with the communications link with the electronic surface…F2-E0Key contact closed for more than 60 secondsF2-E1No communication between keyboard and controlF2-E6STOP/CLEAR key contact closed for more than 60 secondsF20Control has detected a problem with the communications link with the electronic surface…F23Control has detected a problem with the communication link with the Variable Speed…F26Communication failure with Mini Oven Control Board (models equipped with Bake-n-Warm…F3Oven probe problemF3 E4Bottom sensor open (bottom oven sensor open).F3 E5Lower sensor short or bottom sensor short (bottom oven sensor shorted).F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Break in oven sensor circuitF3-E1Short in oven sensor circuitF3-E2BAKE/BROIL temperature out of range (too high)F3-E3Clean temperature out of range (too high)F30Open RTD sensor probe or wiring problem (EOC may initially display F10 thinking a runaway…F31Shorted RTD sensor probe or wiring problem (displayed when oven is in active mode or an…F4 E2Over temperature during cook (temperature runaway during cooking).F4 E3Over temperature during clean (temperature runaway during self-clean).F4 E7Over temperature cavity 2 (temperature runaway error in second cavity).F40Cooktop lockout failure (some models).F41Cooktop lockout error.F5Internal circuit or system failure detected by the ESEC control; the active function is…F5 E2Door switch fault.F5 E4Latch switch fault.F5 E7Unlock door error or cannot unlock door.F5-E0Door and latch switches do not agreeF5-E1Latch switch not operatingF500Loss of LIN Buss communication between EOC and ESEC.F6Electronic control has detected a circuit fault; control stops current operation and…F6 E4Lost communication between power board and display board.F6 E5Cancel key error.F62Missing 60Hz zero-cross synchronization signal from EOC-Relay Board to EOC-Display Board.F7Internal circuit or system failure detected by the ESEC control; the active function is…F700Loss of Display tail #0 on ESEC.F701Loss of Keyboard Tail on ESEC.F702Shorted Keypad on ESEC.F710Loss of Display tail #1 on ESEC.F9Latch motor problemF90Door motor mechanism failureF91Maximum oven door unlock attempts exceeded.F92Door motor mechanism failure (F90 to F94).F93Door motor mechanism failure (F90 to F94).F94Door motor mechanism failure (F90 to F94).F95Door motor mechanism failureHEHot Element indicatorHLdWarm & Hold function is active or ready to activateHOTThe meat probe temperature has exceeded the maximum allowed temperatureLOCOven lock is activePFPower failure indicator displayed on the electronic surface element control panel when…SAbSabbath feature is active on the oven control, indicating the oven is operating in…SbSabbath feature is active on the cooktop displaySDAppliance set for Display Mode (store demo mode).SFSabbath mode failure indicator displayed after a power failure or interruption occurred…SPrSelf-clean cycle was canceled because a cooktop surface burner was turned on during the…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Kenmore error codes
Common questions
How do I find the error code on my Kenmore Range?
Most Kenmore ranges show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Kenmore ranges. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.