mypros+
Error code reference

Kenmore Range Error Code 3d11

Upper oven sensor resistance too high (>3680 ohms)

Kenmore codesKenmore range codes

Upper oven sensor resistance too high (>3680 ohms) – open sensor circuit; disables all cooking functions for the cavity.

First step from the service manual

Check oven temperature sensor and wiring; replace sensor if open.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 3d11.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 3d11 means on a Kenmore range

Error code 3d11 on a Kenmore range indicates that the upper oven temperature sensor is reading a resistance value above 3680 ohms, which falls outside the acceptable operating range. The oven control board interprets this high-resistance reading as an open circuit in the sensor loop, meaning the board cannot receive a valid temperature signal from the upper oven cavity. As a safety and functional response, the control disables all cooking operations for the upper oven until the fault is resolved.

The upper oven temperature sensor is a resistive temperature device, typically a negative temperature coefficient (NTC) or positive temperature coefficient (PTC) probe, whose resistance changes predictably with temperature. When the circuit reads above the maximum threshold of 3680 ohms, the cause is usually a broken sensor element, a disconnected or corroded wiring harness connector, or a wire that has developed an open due to heat damage near the oven cavity. In rarer cases, a failing control board that cannot properly read the sensor input may also produce this fault.

Diagnosis begins at the sensor itself, using a multimeter to measure the sensor's resistance at room temperature and compare it against the expected specification. If the sensor reads open (infinite or excessively high resistance), the sensor requires replacement. If the sensor measures within spec, the wiring harness between the sensor and the control board should be inspected for breaks, loose connectors, or heat-related damage before suspecting the control board.

Source: manufacturer service documentation.

Common causes of 3d11

  1. 01

    Failed oven temperature sensor

    Part replacement

    The sensor probe itself has developed an internal open, causing its resistance to exceed 3680 ohms. Testing the sensor with a multimeter will show infinite or abnormally high resistance rather than the expected in-range value at room temperature.

  2. 02

    Disconnected or loose wiring connector

    Wiring / connection

    The connector at the sensor or at the control board end of the harness may have worked loose over time due to heat cycling and vibration. Inspecting and reseating the connectors can resolve this fault without replacing any parts.

  3. 03

    Damaged or broken sensor wiring harness

    Part replacement

    Wires routed near or through the oven cavity can suffer heat damage, leading to an open circuit within the harness. A visual inspection for frayed, melted, or broken wires along the full harness run from the sensor to the board is necessary.

  4. 04

    Corroded sensor connector terminals

    Wiring / connection

    Moisture or high heat can cause corrosion at the sensor connector pins, increasing resistance in the circuit to the point where the board reads an open. Cleaning the terminals or replacing the connector pigtail may restore a proper circuit.

  5. 05

    Faulty control board

    Part replacement

    If the sensor and all wiring test within specification, the control board's sensor input circuit may have failed, causing it to misread a valid sensor as an open circuit. This is the least common cause and should only be considered after ruling out the sensor and wiring.

See the test procedure for each cause

Frequently asked questions about 3d11

What does 3d11 mean on a Kenmore range?
Error code 3d11 means the control board has detected that the upper oven temperature sensor circuit is reading a resistance above 3680 ohms, which indicates an open circuit. Because the board cannot receive a valid temperature reading, it disables all cooking functions for the upper oven cavity. The most common cause is a failed sensor or a broken wire in the sensor circuit.
Can I fix the 3d11 error myself?
A knowledgeable DIYer can diagnose and fix this error in many cases. Start by unplugging the range and using a multimeter to test the resistance of the upper oven temperature sensor. If the sensor reads open or far above the normal range at room temperature, replacing the sensor is a straightforward repair. If the sensor tests fine, inspect the wiring harness for visible damage or loose connectors before considering a control board replacement.
Is it safe to use my Kenmore range while the 3d11 code is active?
The upper oven is disabled by the control board when this code is present, so attempting to use that cavity for cooking will not work until the fault is cleared. Surface burners and any lower oven cavity may continue to operate depending on the model. You should not attempt to bypass the fault, as the control board disables the upper oven specifically because it cannot monitor temperature safely.
How much does it cost to repair the 3d11 error on a Kenmore range?
If only the temperature sensor needs replacement, repair costs typically fall in the range of $20 to $100 for the part, plus labor if a technician is hired. Wiring harness repairs vary depending on the extent of the damage. A control board replacement, if needed, is the most expensive scenario and can range from $150 to $400 or more for parts alone.
Will resetting the range clear the 3d11 error code?
Resetting the range by cutting power at the breaker or unplugging it may temporarily clear the code from the display, but the error will return as soon as the control board attempts to read the upper oven sensor again. The underlying fault, whether a failed sensor, broken wire, or faulty connector, must be physically repaired before the code will stay cleared and normal oven operation will be restored.

Related Kenmore range codes

All Kenmore range codes
View all 159 Kenmore range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass