mypros+
Error code reference

Kenmore Range Error Code F5-E0

Door and latch switches do not agree

Kenmore codesKenmore range codes

Door and latch switches do not agree - door switch is open (indicating open door) and latch switch is closed (indicating locked door).

First step from the service manual

If door latched: disconnect power, check wires and connectors from control to door switch, replace door switch if wiring is okay.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F5-E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F5-E0 means on a Kenmore range

The F5-E0 error code on a Kenmore range indicates a conflict between two safety switches that monitor the oven door: the door switch and the latch switch. These two switches are designed to work in agreement. When the door is open, the door switch should be open (no continuity) and the latch should be disengaged. When the door is locked for a self-clean cycle, both switches should confirm that locked state. F5-E0 fires when these signals contradict each other, specifically when the door switch reads open (suggesting the door is not fully closed or the switch has failed) while the latch switch reads closed (indicating the door is locked). The control board interprets this disagreement as a fault condition and halts operation.

The most common scenario for this fault is a failed or misaligned door switch. The door switch is a mechanical component that can wear out, become dislodged from its mounting position, or develop an open circuit internally. Wiring issues between the control board and the door switch are also a frequent culprit, including loose connectors, broken wire terminals, or chafed insulation causing an intermittent open in the circuit. Because the latch switch is still reading closed while this fault appears, the latch mechanism itself is typically not the primary suspect.

Diagnosing this code starts with disconnecting power to the range and physically inspecting the wiring harness and connectors that run from the control board to the door switch. Look for loose pins, corrosion, or damaged insulation. If the wiring checks out visually and with a continuity test, the door switch itself should be tested and replaced if it fails to show continuity when the door is in the closed and latched position.

Source: manufacturer service documentation.

Common causes of F5-E0

  1. 01

    Failed door switch

    Part replacement

    The door switch has worn out or developed an internal open circuit, causing it to report an open door even when the door is closed and latched. Testing with a multimeter across the switch terminals will show no continuity when there should be.

  2. 02

    Loose or damaged wiring connector

    Wiring / connection

    The connector between the control board and the door switch can loosen over time or develop corrosion, breaking the circuit and causing the control to read the switch as open. Inspect all connectors in the door switch circuit for secure seating and clean terminals.

  3. 03

    Broken or chafed wire in door switch harness

    Part replacement

    Repeated door opening and closing can stress the wiring harness near the door hinge area, leading to a broken or intermittently open wire. Look for visible damage, especially where the harness bends.

  4. 04

    Misaligned door switch

    Wiring / connection

    The door switch may have shifted out of its mounting position so the door no longer activates it properly even when closed. Check that the switch is firmly seated and that the door striker or actuator tab is making full contact with it.

  5. 05

    Control board fault

    Part replacement

    If the door switch and all wiring test correctly, the control board may be misreading the switch signal due to a failed input circuit. This is the least common cause and should only be suspected after all other components have been ruled out.

See the test procedure for each cause

Frequently asked questions about F5-E0

What does F5-E0 mean on a Kenmore range?
F5-E0 means the door switch and the latch switch are sending conflicting signals to the control board. Specifically, the door switch is reading open (indicating the door is open) while the latch switch is reading closed (indicating the door is locked). This disagreement triggers a fault that prevents normal operation. The root cause is usually a failed door switch or a wiring problem in the door switch circuit.
Can I fix the F5-E0 error myself?
Many technicians and experienced DIYers can resolve this code by inspecting and reseating connectors or replacing the door switch. Start by disconnecting power to the range before doing any inspection. If checking the wiring connections does not resolve the fault, replacing the door switch is the next step and is a manageable repair for someone comfortable working with appliance wiring.
Is it safe to use my Kenmore range while F5-E0 is displayed?
You should not attempt to run a self-clean cycle while this fault is active, since the control cannot confirm the door is properly secured. Surface burners may still function depending on the control logic, but the oven should not be used until the door switch fault is resolved to ensure the door locking system operates correctly.
Will resetting the range clear the F5-E0 error code?
Disconnecting power briefly may clear the code temporarily, but if the underlying hardware fault remains, the error will return once the control rechecks the door switch and latch switch signals. A reset is a useful first step to confirm whether the fault is intermittent, but it does not substitute for diagnosing and repairing the door switch or wiring.
How much does it cost to repair an F5-E0 error on a Kenmore range?
If the fix requires only reseating a connector, there may be no parts cost at all. Replacing the door switch typically runs in the range of $15 to $60 for the part, depending on the specific model. If a technician performs the repair, expect labor costs on top of the part, which can bring the total to somewhere between $100 and $250 depending on your area and the service provider.

Related Kenmore range codes

All Kenmore range codes
View all 159 Kenmore range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass