mypros+
Error code reference

Maytag Dishwasher Error Code Delay LED + Light Wash LED

Motor low current fault detected during Field Service Test.

Maytag codesMaytag dishwasher codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Delay LED + Light Wash LED error code actually means

Your Maytag dishwasher has detected that the wash motor is not drawing enough electrical current to run correctly, which usually means the motor itself is failing or there is a wiring problem between the control board and the motor. The dishwasher caught this issue during its self-test routine. A technician will need to test the motor and its wiring to determine whether the motor or another component needs to be replaced.

Diagnostic procedure

The full Delay LED + Light Wash LED procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Enter Field Service Test to confirm fault; check motor resistance (3-4 ohms) from ST5 to ST8.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Delay LED + Light Wash LED procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Delay LED + Light Wash LED

Ranked by how often they cause this code
  1. 1Failed motor winding
  2. 2Loose or corroded connector at ST5 or ST8
  3. 3Damaged wiring harness
  4. 4Faulty control board motor output

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Delay LED + Light Wash LED

What does Delay LED + Light Wash LED mean on a Maytag dishwasher?
This LED combination indicates a motor low current fault detected during the Field Service Test. The dishwasher's self-diagnostic routine found that the wash motor is not drawing sufficient current to operate correctly. This typically points to a failing motor winding, a wiring issue, or a poor connection at the motor harness. Resistance between connector terminals ST5 and ST8 should measure between 3 and 4 ohms on a properly functioning motor.
Is it safe to keep using my Maytag dishwasher when this fault is showing?
A motor low current fault means the wash motor is not functioning correctly, so the dishwasher will not clean dishes properly during this condition. Continuing to run cycles is unlikely to create an immediate safety hazard, but it will not produce useful results and could stress other components. It is best to diagnose and resolve the fault before regular use.
How much does it cost to repair a Maytag dishwasher motor low current fault?
Repair costs vary depending on the root cause. If the fix is limited to cleaning or reseating a connector, costs may only involve a service call fee, typically in the range of $75 to $150. If the wash motor needs replacement, parts plus labor can range from $200 to $400 or more depending on the specific model and local labor rates. A control board replacement, if needed, falls in a similar or higher cost range.
Can I fix the Delay LED + Light Wash LED fault myself?
A knowledgeable DIYer can perform the initial resistance test between ST5 and ST8 using a multimeter to determine whether the motor or wiring is at fault. Inspecting and reseating harness connectors is also manageable without specialized tools. However, replacing the wash motor or control board requires comfort working with appliance wiring and disassembly, so professional service is recommended if you are unsure.
Will resetting the dishwasher clear this error code?
A power reset may temporarily clear the displayed fault, but the underlying cause remains. If the motor winding resistance is out of spec or a wiring fault exists, the error will return when the Field Service Test is run again or when the dishwasher attempts a normal cycle. The fault should be properly diagnosed and repaired rather than cleared by reset alone.

Related Maytag dishwasher error codes

All Maytag dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass