mypros+
Error code reference

Samsung Dishwasher Error Code 4E2

High temperature water supply error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 4E2 error code actually means

Your Samsung dishwasher has detected that the water coming into the machine is dangerously hot, at or above 80°C (176°F), and has stopped filling to protect itself from damage. This could mean your home's water heater is set too high, or a sensor inside the dishwasher is faulty and giving a false reading. Either way, the dishwasher will not run until the problem is resolved.

Diagnostic procedure

The full 4E2 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check water supply temperature (must be below 80°C). Possible defect: Thermistor, Main PBA.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 4E2 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 4E2

Ranked by how often they cause this code
  1. 1Water heater set too high
  2. 2Faulty thermistor
  3. 3Plumbing cross-connection or mixing valve failure
  4. 4Main PBA fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 4E2

What does 4E2 mean on a Samsung dishwasher?
The 4E2 error code means the dishwasher has detected incoming water at 80°C or above during the fill cycle and has shut down to prevent damage. It points to either an actual high-temperature water supply condition or a faulty thermistor sending an incorrect reading to the control board. The machine will not continue operating until the temperature issue is resolved or the defective component is repaired.
Is it safe to use my dishwasher while the 4E2 code is showing?
No, the dishwasher should not be operated while the 4E2 error is active. The machine has halted the fill cycle as a protective measure, and attempting to bypass or reset the error without addressing the root cause could result in damage to internal components including seals, plastic parts, and the wash tub. Resolve the water temperature or sensor issue before resuming use.
Will resetting the dishwasher clear the 4E2 error?
A power reset may temporarily clear the error code display, but if the underlying cause has not been fixed, the 4E2 code will return as soon as the dishwasher attempts to fill again. A reset is a useful first step to confirm whether the fault is intermittent, but it is not a repair. The water supply temperature and sensor components must be inspected and corrected for a lasting resolution.
Can I fix the 4E2 error myself?
Some causes of 4E2 can be addressed without a technician. Start by checking your water heater thermostat and lowering it if it is set above 60°C. If the supply temperature is normal, the thermistor or Main PBA will need to be tested and potentially replaced, which requires basic electrical diagnostic skills and component sourcing. If you are not comfortable testing electrical components, a qualified appliance technician should handle the repair.
How much does it cost to repair a Samsung dishwasher showing 4E2?
Repair costs depend on the cause. If only the water heater thermostat needs adjustment, there is no parts cost and minimal labor if any. A thermistor replacement typically falls in the range of $20 to $80 for the part, plus labor if a technician is used. Main PBA replacement is more expensive, generally ranging from $100 to $300 or more for the board, plus labor costs that vary by region.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass