Error code reference
Samsung Dishwasher Error Code EE
Abnormal voltage
Abnormal voltage: blackout or DC Link voltage is high or low voltage condition, switches to stop mode.
MyPros+ Max
Get the full diagnostic procedure for EE.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Samsung Dishwasher
EE on my Samsung DW80R5060US
M+
Abnormal voltage: blackout or DC Link voltage
From Service Manual 138996, p.48:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure line voltage at the power cord terminal block. Expected: 120 VAC (L1 to neutral) or 208 to 240 VAC between L1 and L2 under load.
3.Inspect the cord strain relief and terminal block screws for signs of arcing or heat discoloration. Loose connections here mimic an intermittent power failure to the control board.
Part DC96-01043A
Power cord assembly
Related Samsung dishwasher codes
All Samsung dishwasher codes →- 1CLow water level anomaly detected 3 times during a wash…
- 1ELow water level error during wash
- 3CBLDC circulation pump error with sub-codes L1-L6, L8, and…
- 3C1Circulation pump motor error (Inverter PBA related)
- 3C2Circulation pump error variant (same conditions as 3C).
- 3C3Circulation pump error variant (same conditions as 3C).
- 3C4Circulation pump error variant (same conditions as 3C).
- 3C5Circulation pump error variant (same conditions as 3C).
View all 91 Samsung dishwasher codes
- 3ECirculation pump error (sub-codes 3E1 through 3E4)
- 4CFlowmeter in Case Brake does not detect proper pulse counts…
- 4C5Water valve out of water
- 4EWater supply error
- 4E (High Temp Water Supply)High temperature water supply error
- 4E (High temp water)High temp water error
- 4E1Water supply error related to hot water
- 4E2High temperature water supply error
- 4E5Water supply valve out of water
- 5CDrain pump error occurred 4 times; if water level remains…
- 5C (repeated)Drain pump check code occurred 3 times with 3-minute pause…
- 5C1Drain error variant
- 5C2Drain pump error occurred 11 times with 5-minute pause and…
- 5C3Drain pump error occurred 11 times with 5-minute pause and…
- 5C4Drain pump error occurred 11 times with 5-minute pause and…
- 5C5Drain pump error occurred 11 times with 5-minute pause and…
- 5C6BLDC C-pump error with sub-codes C1 (phase current over 2A…
- 5EDrain error
- 6E2Button error
- 7CVane motor/sensor vane error
- 7EVane motor/sensor vane error
- 8CBlackout or DC link voltage is high or low voltage…
- 9CCirculation pump check code
- 9C1Power supply error
- 9C2Power supply error
- 9ELow level sensor error
- 9E1Abnormal voltage error
- ACCommunication between main PBA and sub PBA is abnormal…
- AC2Communication failure
- AC6No response received from inverter PBA for 3 seconds…
- AEMain-Sub PBA communication error
- AE2Main PBA to Inverter PBA communication failure
- AE6BLDC motor communication error
- bCTouch button is pressed and held for continuous 30 seconds…
- bC2Button/key input error
- bC3Touch button communication error
- bEButton/key input error
- bE2Button error
- bE3Key input error
- Button errorFunctional error with the control panel buttons.
- CECommunication error between Micom in sub PBA and Touch IC…
- dCDoor open detected during operation
- dC1Door open information detected only in Inverter Micom…
- dC3Auto Door Open Actuator failure
- dEAuto Door Open device operated but door opening is not…
- dODoor open warning
- Drain errorError indicating the dishwasher cannot drain water properly.
- dWDoor open warning
- E4Low level water error
- FCFan Motor RPM is measured less than 100 rpm; fan motor…
- FC2Fan motor for hot air drying fails
- fEFan Motor RPM is measured less than 100 rpm; fan motor…
- HCHigh temperature heating error
- HC1Heater error
- HC2Drying heater malfunction
- HC4Drying duct temperature is 102 degrees or higher for 3…
- HEHeater error
- HE (Heater)Heater error
- HE (High Temp Heating)High temperature heating error
- HE1High temperature heating error
- HE2Heater overheat error
- High temperature water supply errorIncoming water temperature is too high, possibly above…
- IEInverter communication error
- LCWater leakage detected
- LELow level water error
- LE (Leakage)Leakage error
- Low-level water errorWater supply error indicating insufficient water level.
- nEDrain error.
- OCOverflow detected
- OEOver-level water error
- Over-level water error / Leakage errorFunctional error indicating excessive water level or water…
- PCDistributor motor position error
- PEHalf load/distributor motor error
- tCThermistor error
- tC1Drying duct temperature sensor AD value is 64920 or more…
- tEThermistor error
- tE (High Temp Heating)High temperature heating error
- tE (High temp)High temp error
- tE1Thermistor error
- tE2High temp heating error
- Temperature Sensor error / Heater error / High temperature heating errorFunctional error related to temperature sensor, heater, or…
- WEWater supply error
- WE (High Temp)High temperature water supply error
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass