mypros+
Error code reference

Samsung Range Error Code C-70

Steam sensor is open or short-circuited when steam mode is active.

Samsung codesSamsung range codes

Steam sensor is open or short-circuited when steam mode is active.

First step from the service manual

Check if the main PCB connector has been inserted.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for C-70.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What C-70 means on a Samsung range

The C-70 error code on a Samsung range indicates a fault in the steam sensor circuit that is detected specifically when the oven is operating in steam mode. The steam sensor monitors moisture and temperature conditions inside the oven cavity during steam cooking cycles. When the range's main PCB detects that the steam sensor circuit is either open (broken or disconnected, showing no continuity) or short-circuited (showing near-zero resistance due to a wiring fault or failed component), it triggers the C-70 code and interrupts the steam cooking function to prevent damage to the appliance or unsafe operation.

The most common starting point for diagnosing C-70 is verifying that the connector between the steam sensor harness and the main PCB is fully and correctly seated. A loose or partially inserted connector can mimic the electrical signature of a failed sensor, causing the board to read an open or short condition even when the sensor itself is functional. Connector pins can back out, corrode, or fail to engage properly after service work or vibration over time.

If the connector is confirmed to be properly seated and the error persists, the steam sensor itself may be defective. An open circuit reading suggests the sensor's internal element has failed or a wire in the harness has broken. A short circuit reading points to insulation breakdown, a pinched wire, or internal sensor failure. The main PCB is the least likely culprit but should be considered if the sensor and wiring harness both test within acceptable parameters.

Source: manufacturer service documentation.

Common causes of C-70

  1. 01

    Loose or unseated main PCB connector

    Wiring / connection

    The connector linking the steam sensor harness to the main PCB may not be fully inserted, which causes the board to read a false open or short circuit. This is the first thing to check and requires no parts replacement.

  2. 02

    Defective steam sensor

    Part replacement

    The steam sensor itself may have failed internally, resulting in a true open or short circuit in the sensor element. Testing the sensor for continuity and comparing against expected resistance values will confirm this fault.

  3. 03

    Damaged or broken wiring harness

    Part replacement

    The wiring between the steam sensor and the PCB connector may have a broken conductor or damaged insulation causing an intermittent open or a short to ground. Visually inspect the harness for pinching, burns, or chafing.

  4. 04

    Corroded or damaged connector pins

    Wiring / connection

    Moisture exposure during steam cooking can cause corrosion on the sensor connector pins, increasing resistance enough to trigger an open circuit fault. Inspect the connector terminals closely for discoloration or oxidation.

  5. 05

    Failed main PCB

    Part replacement

    If the sensor, harness, and all connectors test correctly, the main PCB may have failed and is incorrectly reading the steam sensor circuit. This is the least likely cause and should only be considered after all other components are ruled out.

See the test procedure for each cause

Frequently asked questions about C-70

What does C-70 mean on a Samsung range?
The C-70 code means the range has detected that the steam sensor circuit is either open or short-circuited while steam mode is active. This fault causes the steam cooking function to stop operating. The issue can stem from a loose PCB connector, a faulty steam sensor, or damaged wiring.
Can I fix the C-70 error myself, or do I need a technician?
A homeowner comfortable working around appliances can start by checking whether the main PCB connector is fully seated, which requires accessing the back of the range. If the connector is secure and the error remains, testing the steam sensor and wiring harness requires a multimeter and some technical knowledge. A professional technician is recommended if the sensor or PCB needs to be replaced.
Is it safe to use my Samsung range while the C-70 error is displayed?
The C-70 error will prevent steam mode from operating, but standard bake and broil functions may still be available depending on the model. It is not advisable to continue attempting steam cooking cycles while this fault is active, as the sensor monitoring that mode is not functioning. Address the fault before resuming steam cooking to avoid potential issues.
How much does it cost to repair a C-70 error on a Samsung range?
If the fix is simply reseating a loose connector, there is no parts cost involved. Replacing a faulty steam sensor typically costs in the range of $30 to $80 for the part, plus labor if a technician is hired. A main PCB replacement, if required, is a more significant expense and can range from $150 to $400 or more depending on the specific model.
Will resetting the Samsung range clear the C-70 error code?
Performing a reset by powering the range off at the circuit breaker for a few minutes may temporarily clear the C-70 code, but it will return if the underlying fault has not been corrected. A reset does not repair a faulty sensor, damaged wiring, or a loose connector. The root cause must be diagnosed and corrected for the code to stay cleared.

Related Samsung range codes

All Samsung range codes
View all 72 Samsung range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass