Skip to main content
Error code reference
Samsung Range Error Codes
80 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
-dC-Divider sensing information error (divider not properly inserted or removed for selected…-dE-Partition switch error.-E-2E-Meat probe error (partition switch / probe circuit error).-tE-Sub PCB communication error between touch glass and Sub PCB.1c1cShorted key detected1c2cKeyboard tail disconnected1c31Cancel key circuit problem1c6cEEPROM error1c7cControl not calibrated1c8cCooking program error1d11Runaway temperature (650°F) with door unlocked1d21Runaway temperature (950°F) with door locked3d11Oven temperature sensor open3d21Oven temperature sensor shorted4d11Door switch not closed when door is locked.4d51Door switch not open or closed9d11Latch will not lockA2DC Motor Locking ErrorbAd LInEPower connection is installed improperly (incorrect L1, L2, N terminal block wiring).boIGBT (Insulated Gate Bipolar Transistor) sensor open (high resistance) error on inverter…bsIGBT (Insulated Gate Bipolar Transistor) sensor short (low resistance) error on inverter…C-20Oven temperature sensor open circuit (resistance above 2950 ohms) or short circuit…C-21Oven overheating or safety errorC-22The sub PCB sensor is open when the oven is operating, or there is a short in the sub PCB…C-23Temperature probe (meat probe) sensor is shorted when oven is operating.C-24Oven vent blockedC-30The main PCB temperature sensor is open when the oven is operating, or there is a short…C-31PCB temperature overC-70Steam sensor is open or short-circuited when steam mode is active.C-72Drainage system problemC-A2BLDC motor operate informationC-d0Shorted key errorC-d1Door locking malfunctionC-d4Door opening information errorC-d5Door lock is mispositioned or door locking error.C-F0Communication error between main module (oven) and sub module (oven), main module (oven)…C-F2Communication between the Sub PCB and touch panel is interrupted, or touch key is shorted…C0Top Sensor Open Error (A/D value rises over 252 or ambient temperature below -10°C) or…C1Over Temperature ErrorC2IGBT Sensor Open Error (A/D value rises over 239) or IGBT Sensor Short Error (A/D value…CEUART communication errorE-08Oven heating errorE-0AOven heating overE-0CPartition switch errorE-0EDoor locking errorE-21Oven temperature sensor open circuit (resistance over 2950 ohms).E-22Oven temperature sensor shorted (resistance under 930 ohms).E-24Oven overheating errorE-27Oven sensor opened (resistance over 2950 ohms), detected 20 seconds after oven starts…E-28Oven sensor shorted (resistance under 930-940 ohms), detected 20 seconds after oven…E-53EEPROM error.E-83Main PCB communication error between Main PCB and Sub PCB.E-84Communication error from cooktop to ovenE-85Communication errorE-OEDoor locking error.F0Communications ErrorF2Communication error between induction sub module and touch panel.IGBT Sensor OpenIGBT sensor (Assy-Inverter Module) open errorIGBT Sensor ShortIGBT sensor (Assy-Inverter Module) short errorKey ShortTouch button short errorLELow voltage errorLine ErrorPower supply cable is incorrectly installed or the power connection is improperly wired.Low VoltageLow voltage errorLow Voltage ErrorDC 12V has dropped under 9V, possibly due to defects of PCB or wiring.OTOver temperature error; occurs when the temperature of the top sensor rises very high.Over TemperatureOver temperature errorOver Temperature ErrorTop sensor temperature rises excessivelyPan DetectionPan detection error; occurs when cookware is unsuitable, too small, or no cookware has…Pan Detection ErrorCookware is unsuitable, too small, or no cookware has been placed on the cooking zone.PDPan detection error; occurs when cookware is unsuitable, too small, or no cookware has…SEShorted key error on control panelSE2Oven sensor opened problem.SE3Oven sensor shorted problem.SE4Oven heating error.SE5Oven overheating.SE6Door locking error.toTop sensor open error; occurs when there is an open sensor, disconnected wires, or a…Top Sensor OpenTop sensor (cooktop) open errorTop Sensor ShortTop sensor (cooktop) short errortsTop sensor short error; occurs when there is a shorted sensor, wires, or a defective PCB.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.