mypros+
Error code reference

Samsung Refrigerator Error Code F-1 segment g

F-DEFROST error (Freezer defrost heater failure

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F-1 segment g error code actually means

Your Samsung refrigerator is showing this error because the freezer's automatic defrost cycle did not finish in time, meaning ice is likely building up inside the freezer on the cooling coils. This is usually caused by a burned-out defrost heater, a blown thermal fuse, or a related safety component that stopped the heater from running. If left unchecked, your freezer and refrigerator will gradually lose their ability to stay cold.

Diagnostic procedure

The full F-1 segment g procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Remove MAIN PCB CN71 connector and read continuity between White and Orange wires; 0 Ohm indicates heater short, infinity Ohm indicates Wire/Thermal Fuse or Bimetal is open.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F-1 segment g procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F-1 segment g

Ranked by how often they cause this code
  1. 1Open thermal fuse or bimetal thermostat
  2. 2Failed defrost heater
  3. 3Damaged or broken wiring harness
  4. 4Faulty main PCB

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F-1 segment g

What does F-1 segment g mean on a Samsung refrigerator?
F-1 segment g indicates a freezer defrost failure on Samsung T, E, and W model refrigerators. It means the defrost cycle did not complete within the 70-minute time limit allowed by the control board. The fault is typically located in the defrost heater, thermal fuse, bimetal thermostat, or the wiring connecting these components. Ice buildup on the evaporator coil is a common secondary symptom.
Is it safe to keep using my Samsung refrigerator when this error appears?
Continuing to run the refrigerator with an active F-1 segment g error is not advisable for extended periods. Without a functioning defrost cycle, ice will accumulate on the evaporator coil and progressively block airflow, causing both the freezer and refrigerator compartments to warm up. Food safety can become a concern as temperatures rise, so the fault should be diagnosed and repaired promptly.
How much does it cost to repair the F-1 segment g error on a Samsung refrigerator?
Repair costs vary depending on which component has failed. A thermal fuse or bimetal thermostat typically costs between $5 and $25 for the part alone, while a defrost heater assembly can range from $20 to $80. If professional labor is needed, total repair costs including parts and service can range from $100 to $300 or more depending on your location and the extent of the repair.
Can I fix the F-1 segment g error myself?
A knowledgeable DIYer can perform the initial diagnosis by disconnecting the CN71 connector on the main PCB and reading continuity between the White and Orange wires with a multimeter. A 0 Ohm reading points to a shorted heater, and an infinity reading points to an open thermal fuse, bimetal thermostat, or broken wire. Replacing these individual components is within reach for someone comfortable working with appliance wiring, but if the main PCB is suspected, professional service is recommended.
Will resetting the refrigerator clear the F-1 segment g error?
Resetting the refrigerator by unplugging it may temporarily clear the error display, but the underlying fault will remain. The error will return once the control board attempts and fails to complete another defrost cycle. A proper repair requires identifying and replacing the failed component, whether that is the heater, thermal fuse, bimetal thermostat, or wiring.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass