mypros+
Error code reference

Samsung Refrigerator Error Code FZ-Ice Pipe Heater

Error occurs when there is a wire connector slip-out of the water supply pipe heater, a contact error, or a breakage in the wiring.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the FZ-Ice Pipe Heater error code actually means

This error means your Samsung refrigerator has detected a problem with the small heater that keeps the water supply line in the freezer from freezing over. Without this heater working correctly, your refrigerator cannot make ice reliably. The issue is usually a loose wire connection, a damaged wire, or a failed heater element.

Diagnostic procedure

The full FZ-Ice Pipe Heater procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Measure resistance of Main PCB CN79 Yellow-Pink wires; should be within 102 ohm ±7%. 0 ohm = heater short, infinity = check for wire open or connector slip-out.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock FZ-Ice Pipe Heater procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of FZ-Ice Pipe Heater

Ranked by how often they cause this code
  1. 1Connector slip-out at CN79
  2. 2Wiring harness breakage
  3. 3Contact corrosion or poor terminal connection
  4. 4Shorted heater element
  5. 5Open heater element failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about FZ-Ice Pipe Heater

What does FZ-Ice Pipe Heater mean on a Samsung refrigerator?
This error code indicates a fault in the freezer water supply pipe heater circuit. The refrigerator has detected a wire connector slip-out, a wiring contact error, or a breakage in the heater wiring. The heater keeps the water supply line from freezing so that ice can be produced. Diagnosing the specific cause requires measuring resistance at Main PCB connector CN79 on the Yellow and Pink wires.
Is the FZ-Ice Pipe Heater error dangerous?
This fault is not an immediate safety hazard to your household. However, a shorted heater element can draw excessive current through the circuit, which could cause further damage to the Main PCB or wiring harness if left unaddressed. It is best to diagnose and resolve this error promptly rather than continuing to operate the refrigerator with an unresolved electrical fault.
How much does it cost to repair the FZ-Ice Pipe Heater error on a Samsung refrigerator?
Repair costs vary depending on the root cause. If the fix is simply reseating a loose connector, there may be no parts cost at all, though a service call fee will still apply if you use a technician. Wiring harness repairs or heater element replacements typically add parts costs on top of labor, with total repair estimates generally ranging from around $100 to $300 or more depending on your location and the parts required.
How do I fix the FZ-Ice Pipe Heater error on my Samsung refrigerator?
Start by measuring resistance at the CN79 connector on the Main PCB using the Yellow and Pink wires. A correct reading is 102 ohms plus or minus 7%. If you read 0 ohms, the heater has shorted and needs replacement. If you read infinity, inspect the wiring harness for breaks and check that the connector is fully seated. Reseating a loose connector or repairing a damaged wire may resolve the error without replacing any parts.
Will resetting my Samsung refrigerator clear the FZ-Ice Pipe Heater error?
A reset may temporarily clear the error code from the display, but the code will return if the underlying wiring or heater fault is still present. The control board will re-detect the abnormal resistance condition in the CN79 circuit and trigger the error again. A permanent fix requires identifying and correcting the connector, wiring, or heater issue causing the fault.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass