mypros+
Error code reference

Samsung Refrigerator Error Code Ice Maker Sensor Error (Cubed)

Cubed ice maker temperature sensor has failed or is out of range.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Ice Maker Sensor Error (Cubed) error code actually means

This error means your Samsung refrigerator has detected a problem with the temperature sensor inside the cubed ice maker. The sensor is not reading correctly, so the refrigerator cannot properly control or monitor the ice making process. As a result, the cubed ice maker may stop working until the issue is resolved.

Diagnostic procedure

The full Ice Maker Sensor Error (Cubed) procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check voltage of MAIN PCB CN90-"14" ↔ "26" shall be between 4.5V~1.0V.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Ice Maker Sensor Error (Cubed) procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Ice Maker Sensor Error (Cubed)

Ranked by how often they cause this code
  1. 1Failed ice maker thermistor
  2. 2Damaged or broken wiring harness
  3. 3Corroded or loose connector at CN90
  4. 4Ice maker assembly fault
  5. 5Main PCB fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Ice Maker Sensor Error (Cubed)

What does Ice Maker Sensor Error (Cubed) mean on a Samsung refrigerator?
This error code means the temperature sensor in the cubed ice maker has failed or is reporting a value outside the acceptable range. The main PCB monitors this sensor through connector CN90 pins 14 and 26, where the voltage should fall between 1.0V and 4.5V during normal operation. When the signal falls outside that window, the refrigerator logs the fault and may disable the cubed ice maker until the issue is corrected.
Is it safe to keep using my refrigerator when this error is showing?
The refrigerator itself will generally continue cooling and the freezer will remain operational. However, the cubed ice maker may be suspended or unreliable while the sensor fault is active. There is no immediate safety hazard to food storage, but you should address the error promptly to restore full ice maker function and prevent any secondary issues.
Will resetting my Samsung refrigerator clear the Ice Maker Sensor Error (Cubed)?
A reset may temporarily clear the error code from the display, but if the underlying sensor, wiring, or connector fault still exists, the code will return once the refrigerator runs its diagnostics again. Resetting can be a useful step to confirm whether the fault is intermittent or persistent, but it does not fix the root cause. A proper voltage check at CN90 pins 14 and 26 is needed to determine whether a physical repair is required.
Can I fix the Ice Maker Sensor Error (Cubed) myself?
A knowledgeable DIYer can perform basic diagnostics, including inspecting the wiring harness for damage and checking the connector at CN90 for corrosion or loose pins. Measuring the voltage at CN90 pins 14 and 26 with a multimeter will tell you whether the sensor circuit is open, shorted, or within range. If the thermistor or wiring needs replacement, the repair is straightforward but does require accessing the ice maker assembly and potentially removing components in the freezer.
How much does it cost to repair the Ice Maker Sensor Error (Cubed) on a Samsung refrigerator?
If only the thermistor or sensor harness needs replacement, parts typically cost anywhere from $15 to $60 depending on the specific assembly required. If the full ice maker module must be replaced, parts alone can range from $80 to $200 or more. Adding professional labor, total repair costs commonly fall between $100 and $350, depending on the diagnosis and parts involved.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass