mypros+
Error code reference

U-Line Refrigerator Error Code LED 2 flashing

Open thermistor detected

U-Line codesU-Line refrigerator codes

Open thermistor detected – one or more thermistors (bin sensor, liquid line sensor, or refrigerator sensor) has failed or is out of limits.

First step from the service manual

Refer to Thermistors section; check thermistor continuity and resistance. If bin sensor or liquid line sensor fails, refrigerator continues but ice making shuts down. If refrigerator sensor fails, refrigerator shuts down but ice maker continues.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for LED 2 flashing.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What LED 2 flashing means on a U-Line refrigerator

The LED 2 flashing error on a U-Line refrigerator indicates that the control board has detected an open thermistor circuit. Thermistors are temperature-sensing resistors whose resistance changes predictably with temperature. When the control reads resistance values outside the expected range, or detects a completely open circuit, it triggers this fault. The three thermistors involved are the bin sensor (monitoring the ice bin fill level or temperature), the liquid line sensor (monitoring refrigerant line temperature), and the refrigerator sensor (monitoring the cabinet interior temperature).

The behavior of the unit after this fault depends entirely on which thermistor has failed. If the bin sensor or the liquid line sensor is the source of the open circuit, the refrigerator compartment continues to operate normally and maintain temperature, but ice production is suspended until the fault is resolved. If the refrigerator sensor is the failed component, the refrigerator section shuts down entirely while the ice maker continues to operate. This distinction is important during diagnosis because it helps narrow down which sensor to inspect first based on what the unit is or is not doing.

The most reliable diagnostic approach is to check each thermistor for continuity and measure its resistance, then compare that reading against the expected resistance values for the current ambient temperature. An open circuit reading or a resistance value far outside the normal range confirms a failed thermistor. Wiring harness integrity between the thermistor and the control board should also be inspected, since a broken wire or corroded connector can produce the same open-circuit condition as a failed sensor.

Source: manufacturer service documentation.

Common causes of LED 2 flashing

  1. 01

    Failed thermistor sensor

    Part replacement

    A thermistor that has developed an open circuit internally will produce a resistance reading outside acceptable limits. Checking the suspect sensor with a multimeter for continuity and resistance will confirm failure.

  2. 02

    Corroded or loose connector

    Wiring / connection

    Moisture inside a refrigerator environment can corrode the connector terminals between a thermistor and the wiring harness, creating an intermittent or permanent open circuit. Inspect each thermistor connector for corrosion, looseness, or pushed-back pins.

  3. 03

    Damaged wiring harness

    Wiring / connection

    A wire routed near a moving component or sharp edge can develop a break in the conductor while the insulation remains intact, making the fault difficult to spot visually. Pulling gently along each harness run while monitoring continuity can reveal a broken wire.

  4. 04

    Thermistor pulled out of its mounting position

    Wiring / connection

    If a thermistor probe is dislodged from its clip or bracket, it may read temperatures far outside the expected range, causing the control board to flag the circuit as out of limits. Verify each thermistor is seated properly in its designated location.

  5. 05

    Control board fault

    Part replacement

    If all three thermistors and associated wiring check out correctly, the control board input circuit itself may have failed and is misreading valid sensor signals. This is the least common cause and should be diagnosed only after the sensors and wiring are confirmed good.

See the test procedure for each cause

Frequently asked questions about LED 2 flashing

What does LED 2 flashing mean on a U-Line refrigerator?
LED 2 flashing indicates the control board has detected an open or out-of-limits thermistor. The fault can originate from the bin sensor, the liquid line sensor, or the refrigerator sensor. Which sensor has failed determines whether the refrigerator shuts down or the ice maker shuts down. A resistance and continuity check on each thermistor is the first step toward identifying the source.
Can I fix the LED 2 flashing error myself?
A knowledgeable DIYer can diagnose this fault using a multimeter to test thermistor continuity and resistance. If the problem turns out to be a loose connector or a dislodged probe, no parts are needed and the fix is straightforward. If a thermistor has failed internally, replacing it requires sourcing the correct replacement sensor for your specific U-Line model. If the control board is suspected, professional service is recommended.
Is it safe to keep using my U-Line refrigerator while LED 2 is flashing?
It depends on which thermistor has failed. If only the bin or liquid line sensor is at fault, the refrigerator continues to cool and food safety is not immediately compromised, though ice making will be inactive. If the refrigerator sensor has failed, the refrigerator compartment shuts down and food should be relocated promptly to prevent spoilage. Address the fault as soon as possible regardless of which sensor is involved.
How much does it cost to repair the LED 2 flashing error on a U-Line refrigerator?
If the repair involves only cleaning or reseating a connector, costs are minimal and limited to your time. Replacing a failed thermistor sensor typically costs between $20 and $80 for the part, plus labor if you use a technician. A service call for diagnosis and repair can range from $100 to $300 or more depending on your location and what components need replacement. Replacing the control board is the most expensive scenario and can add significantly to the total cost.
Will resetting my U-Line refrigerator clear the LED 2 flashing error?
A power reset may temporarily clear the fault code, but if an open or out-of-limits thermistor is still present, the LED 2 error will return once the control board completes its self-check. Resetting without correcting the underlying problem does not resolve the issue and may delay a necessary repair. The thermistors must be tested and the faulty component repaired or replaced to clear the fault permanently.

Related U-Line refrigerator codes

All U-Line refrigerator codes
View all 52 U-Line refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass