mypros+
Error code reference

Viking Range Error Code RTD

Oven probe (RTD/Resistive Thermal Device) error indicated by the Cycle light flashing 1 second ON, 1 second OFF while the Clean light remains OFF.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the RTD error code actually means

Your Viking oven is detecting a problem with the temperature sensor inside the oven cavity. This sensor tells the oven how hot it is, and the oven cannot safely heat or maintain temperature without a working sensor. The flashing Cycle light is how the oven alerts you to this specific problem.

Diagnostic procedure

The full RTD procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check RTD sensor resistance (should be approximately 1100 ohms at 75°F) at P15 pin 1 to pin 2.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock RTD procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of RTD

Ranked by how often they cause this code
  1. 1Failed RTD Sensor Probe
  2. 2Open or Broken Sensor Wiring
  3. 3Corroded or Loose P15 Connector
  4. 4Shorted RTD Circuit
  5. 5Faulty Control Board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about RTD

What does RTD mean on a Viking range?
RTD stands for Resistive Thermal Device, which is the temperature sensing probe located inside the oven cavity. The RTD error code means the control board is detecting a resistance reading from that probe outside of the normal operating range. The fault is indicated by the Cycle light flashing 1 second on and 1 second off while the Clean light stays off. The oven will not operate normally until the fault is resolved.
Is it safe to use my Viking range when the RTD error is showing?
You should not use the oven when the RTD error is active. Without a functioning temperature sensor, the control board cannot accurately regulate oven temperature, which creates a risk of overheating or unpredictable heating behavior. The cooktop burners on a gas model may still function, but the oven should remain off until the fault is diagnosed and repaired.
Will resetting my Viking range clear the RTD error code?
Resetting the range by cycling power may temporarily clear the error display, but the code will return if the underlying fault in the RTD circuit is still present. A reset does not repair a failed sensor, broken wiring, or faulty board connection. The only way to permanently clear the code is to identify and correct the root cause of the resistance fault in the RTD circuit.
Can I fix the RTD error on my Viking range myself?
A knowledgeable DIYer can perform the basic diagnostic step of measuring resistance at connector P15 pins 1 and 2 with a multimeter. The RTD sensor should read approximately 1100 ohms at 75 degrees Fahrenheit, and a reading far above or below that points to a failed probe or wiring issue. Replacing the RTD probe is a manageable repair if you are comfortable working with appliance wiring. However, if the board itself is at fault, professional service is recommended.
How much does it cost to repair the RTD error on a Viking range?
If the RTD probe is the cause, the part itself typically costs in the range of $30 to $80 depending on the specific Viking model. Professional labor to diagnose and replace the sensor generally adds $100 to $200 or more depending on your area and service provider. If the control board is at fault, board replacement costs are significantly higher, often in the range of $200 to $500 or more for parts alone.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass