Skip to main content
Error code reference
Viking Range Error Codes
109 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1Induction element is not recognizing a compatible cooking vessel, or residual heat is…1 flashNormal operation (idle and active states) on DSI board.1 flash every 4 secNormal operation (idle and active states) on DSI board.1 flash every 4 secondsNormal operation (idle and active states)10Wrong terminal connected-secondary voltage of the power supply above 400 volts.2Safeguard fault2 flashesRTD (Oven Probe) error2 flashes (DSI)DSI control fault.2 flashes + Clean ONModel error on the self-cleaning oven control board (30", 36" and 48" RH oven).2 flashes every 4 secDSI control fault.2 flashes every 4 secondsControl fault on the DSI module.2 flashes every 4 seconds (DSI)Control fault on DSI module.2 flashes then 4 seconds OFFRTD (Oven Probe) error displayed on cycle light on control panel.2 flashes then 4 seconds OFF (cycle light)RTD (Oven Probe) error.3Ignition lockout3 flashesIgnition lockout3 flashes (DSI)Ignition lockout3 flashes + Clean ONA/D Stuck error on the self-cleaning oven control board (30", 36" and 48" RH oven).3 flashes every 4 secIgnition lockout3 flashes every 4 secondsIgnition lockout3 flashes then 4 seconds OFFModel Header error displayed on cycle light on control panel.3 flashes then 4 seconds OFF (cycle light)Model Header error.4Incorrect setup data or configuration error between interface board and induction…4 flashesGas solenoid fault.4 flashes (DSI)Gas solenoid fault.4 flashes + Clean ONFan Hall error on the self-cleaning oven control board (30", 36" and 48" RH oven).4 flashes every 4 secGas solenoid fault on DSI board.4 flashes every 4 secondsGas solenoid fault.5Communication error between interface board and induction generator-interface board cable…5 flashesDSI control fault.5 flashes (DSI)DSI control fault.5 flashes every 4 secDSI control fault.5 flashes every 4 secondsControl fault on the DSI module.6Error on filter board6 flashesGas solenoid fault.6 flashes (DSI)Gas solenoid fault.6 flashes every 4 secGas solenoid fault on DSI board.6 flashes every 4 secondsGas solenoid fault.7Voltage supply error7 flashesPower up with channel on.7 flashes DSIPower up with channel on7 flashes every 4 secPower up with channel on7 flashes every 4 secondsPower supplied to unit with knob(s) in ON position.8Power up lock out / Valve drive fault8 flashesGas solenoid fault.8 flashes (DSI)Gas solenoid fault.8 flashes every 4 secGas solenoid fault on DSI board.8 flashes every 4 secondsGas solenoid fault.9Temperature sensor defectiveA/D StuckA/D converter stuck error indicated by Cycle light flashing 3 times then 4 seconds OFF…A/D Stuck LED (Cycle light 3 flashes then 4s OFF, Clean light ON)A/D converter stuck error on self-clean oven control board.CommLoose communication link between EOC4 and VDSC, or RS485 serial communication is lost or…CoolingCooling fan speed input (Hall Effect sensor) indicates the fan is not running or EOC4 is…Cooling FanCooling fan error indicated by 3 flashes on the Cycle light while the Clean light remains…Cycle 1s ON-1s OFF / Clean OFFRTD (Oven Probe) error on 30", 36" and 48" RH oven.Cycle 2 flashes / Clean ONModel error on 30", 36" and 48" RH oven self-cleaning oven control board.Cycle 3 flashes / Clean ONA/D Stuck error on 30", 36" and 48" RH oven self-cleaning oven control board.Cycle 4 flashes / Clean ONFan Hall error on 30", 36" and 48" RH oven self-cleaning oven control board.Cycle blinking / Clean OFFRTD (Oven Probe) error on the self-cleaning oven control board (30", 36" and 48" RH oven).Cycle flashing / Clean OFFRTD (Oven Probe) error on 30", 36" and 48" RH oven.Cycle light 1s ON/1s OFF, Clean light OFFRTD (Oven Probe) error.Cycle light 2 flashesRTD (Oven Probe) error displayed on control panel cycle light.Cycle light 2 flashes then 4s OFF, Clean light ONModel error.Cycle light 3 flashesModel Header error displayed on control panel cycle light.Cycle light 3 flashes then 4s OFF, Clean light ONA/D Stuck error.Cycle light 4 flashes then 4s OFF, Clean light ONFan Hall error.Cycle light OFF, Clean light 1s ON/1s OFFLatch error.Cycle OFF / Clean 1s ON-1s OFFLatch error on 30", 36" and 48" RH oven self-cleaning oven control board.Cycle OFF / Clean blinkingLatch error on the self-cleaning oven control board (30", 36" and 48" RH oven).Cycle OFF / Clean flashingLatch error on 30", 36" and 48" RH oven self-cleaning oven control board.DoorThe door is open during CLEAN (either the door latch has failed, the door sensor has…Door LatchDoor latch unit in clean mode takes greater than one minute to lock, or door lock is not…DSI 1 FlashNormal operation (idle and active states)DSI 2 FlashesDSI control faultDSI 3 FlashesIgnition lockoutDSI 4 FlashesGas solenoid faultDSI 5 FlashesDSI control faultDSI 6 FlashesGas solenoid faultDSI 7 FlashesPower up with channel onDSI 8 FlashesGas solenoid faultDSI LED ContinuousDSI control fault indicated by LED on continuously.DSI No LEDNo power to the DSI moduleEr31Interface error caused by swapping interface boards/induction adapters or using incorrect…F1Electronic oven control has detected a fault condition in its internal circuitry or…F3Electronic oven control has detected a fault condition in its internal circuitry or…F9Electronic oven control has detected a fault condition in its internal circuitry or…Fan HallFan Hall sensor error indicated by Cycle light flashing 4 times then 4 seconds OFF with…Fan Hall Effect LED (Cycle light 4 flashes then 4s OFF, Clean light ON)Fan hall effect sensor error on self-clean oven control board.High LimitHigh temperature limit error detected; the cycle light flashes 4 times and the clean…Improper Self-Clean SelectionConsumer attempted to set a delayed self-clean cycle, which is not permitted.Key ShortKey press input seen for over 30 seconds.KeyboardInternal disconnection sensed between the VDSC-tactile key PCB and the VDSC-display PCB…LatchDoor latch fault indicated by the cycle light OFF and the clean light flashing 1 second…Latch LED (Clean light flashing 1s ON/1s OFF, Cycle light OFF)Latch error on self-clean oven control board.LED ON continuouslyControl fault on the DSI module.Meat ProbeMeat probe shorted or operation inconsistent with expected operation.ModelModel identification error indicated by the Cycle Light flashing 1 second ON, 1 second…Model HeaderNo model header on EOC4 or incorrect model header for VDSCModel Header LED (Cycle light 2 flashes then 4s OFF, Clean light ON)Model header error on self-clean oven control board.No LEDNo power to the DSI (Direct Spark Module)No ProbeMeat probe input is open (not connected).RTDOven probe (RTD/Resistive Thermal Device) error indicated by the Cycle light flashing 1…RTD (Griddle)Griddle RTD probe fault indicated by 2 flashes of the griddle cycle light followed by 4…RTD (Oven Probe)Oven RTD probe faultRTD (Oven)Oven RTD probe fault indicated by cycle light flashing 1 second ON/1 second OFF and clean…RTD LED (Cycle light flashing 1s ON/1s OFF, Clean light OFF)RTD (oven probe) error on self-clean oven control board.RTD ProbRTD oven temperature sensor is open or shorted.RunawayControl detects temperature rising well past the set point exceeding 650°F for longer…Runaway Oven TemperatureControl detects temperature rising well past the set point and exceeds the maximum limit…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.