Skip to main content
Error code reference
Viking Dishwasher Error Codes
104 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1-1Moisture sensor disconnect-moisture sensor reads out of normal range.1-2Motor Control Status Error1-3Motor control comms error-main control cannot successfully communicate with the motor…1-4Diverter timeout-main control activates the diverter but never sees feedback from the…15Drain Error (NON pressure sensor models)2-1Fill Error (NON pressure sensor models)2-2Fill Error (pressure sensor models)-during a fill, the pressure sensor output does not…2-3User Interface2-3 (service cycle only)Drain Pump Error2-4High level error-pressure sensor indicates a water level higher than the high level…2-5High Level Error3-1User Interface3-2Pump Flow Error3-3Pump Flow Error3-4Motor status error-motor control communicates a motor operation failure mode most likely…3-5Motor undervoltage error-motor control communicates a low motor control voltage condition…4-1Temperature sensor error-temperature sensor reads out of range.4-2Wash heater error-wash heater current sense is out of range (450 model only, service…4-3Dispenser Error4-4Inlet Valve Error4-5Fill too Fast Error5-1Vent Error5-2Blower error-blower current sense is out of range (450 model only, service cycle only).5-3Dry heater error-dry heater current sense is out of range (450 model only, service cycle…5-4Current Sense Error5-5Internal error-main control or UI detects a board level failure.AC Power LossPower loss occurred during a running cycle.All flashPower loss detected.All LEDs flash (except start)AC power loss-power loss occurred during a running cycle.All LEDs flash but startAC Power LossBoth flashPan moisture detectedCirculate Time OutCirculation motor operation has timed out during the wash cycle.Counter Error - User InterfaceCounter error detected in the user interface board.Cycle Error - CirculationCirculation motor or circulation cycle error detected.Cycle Error - DrainDrain cycle error detected; unit unable to complete drain operation.Cycle Error - Error handlerGeneral cycle error detected by the error handler routine.Cycle Error - Fill Sensor ErrorFill sensor detected an error during the fill cycle.Cycle Error - Motor ControllerInternal control processor error related to the motor controller during a cycle.Data processorInternal data processor error detected on the control board.Diverter ErrorThe wash diverter motor is not operating or responding correctly.Drain ErrorWater is not draining properly from the tub; drain system fault detected.E:01Overflow condition detectedE:02No water faultE:03Heater faultE:04Turbidity sensor faultE:05Wash diverter valve faultE:06NTC faultE:07Water inlet valve faultE:08Main board communication faultE:09Display board communication faultE:10User interface board communication faultE:11Conducto probe faultE:12Conductor short circuit faultE:13Pressure switch faultE:15Water counter faultE:16Drain pump blocked faultE:17Auto detergent motor positioning faultE:18Low voltage error.ECONO WASH + LED1Counter ErrorECONO WASH + LED2High Water LevelECONO WASH + LED3Cycle ErrorECONO WASH + LED4Circulate Time OutFill ErrorUnit is not filling with water properly; water supply or fill valve fault detected.Flash all LEDsAC power loss-power loss occurred during a running cycle.Flash all LEDs but startMoisture Sensor water detectionFlash all LEDs but start and run continuouslyAC power loss-power loss occurred during a running cycle.Flash both LED1 and LED2AC Power LossFlash both LED1 and LED2 continuouslyMoisture sensor water detection-moisture sensor output is equivalent to water in the pan.Flash LED1+LED2Moisture sensor water detection-moisture sensor output is equivalent to water in the base…High Water LevelWater level in the tub has exceeded the normal maximum level.LED1+LED2 flash continuouslyMoisture SensorLIGHT CHINA + LED1State ErrorLIGHT CHINA + LED2State ErrorLow Level ErrorWater level in the tub is below the minimum required level.Moisture Sensor - water detectionMoisture sensor output is equivalent to water in the base pan.Moisture Sensor ActivatedWater detected in the base pan by the moisture (flood) sensor.Moisture Sensor DisconnectThe moisture sensor circuit is open or disconnected from the control board.Motor Control Communication ErrorCommunication failure between the motor controller and the main control board.Motor Control Status ErrorMotor controller reports a status error; possible wash motor or controller fault.NORMAL WASH + LED1Moisture Sensor ActivatedNORMAL WASH + LED2Pressure Sensor DisconnectNORMAL WASH + LED3Cycle ErrorNORMAL WASH + LED4User InterfaceNORMAL WASH + LED5Cycle ErrorNORMAL WASH + LED6Sensor ErrorPan Moisture (both lights flash continuously)Water detected in the base pan by the moisture sensor.Pan Moisture (both lights flash)Water detected in the base pan by the moisture sensor.POTS PANS + LED1Drain ErrorPOTS PANS + LED2Fill ErrorPOTS PANS + LED3Moisture Sensor DisconnectPOTS PANS + LED4Temperature Sensor DisconnectPOTS PANS + LED5Cycle ErrorPOTS PANS + LED6Motor Control Communication ErrorPOTS PANS + LED7Motor Control Status ErrorPOTS PANS + LED8Cycle ErrorPOTS PANS + LED9Diverter ErrorPower Loss (all lights except START and RUN flash continuously)Power loss detected.Power Loss (all lights flash)Power loss detected; all lights except START and RUN flash continuously.Pressure Sensor DisconnectThe pressure sensor (HUBA) harness is disconnected or the sensor has failed.RINSE HOLD + LED1Low Level ErrorState Error - Main ControlMain control board has entered an invalid state.State Error - User interfaceUser interface has entered an invalid state.Temperature Sensor DisconnectThe water temperature sensor circuit is open or disconnected from the control board.User Interface - Machine Control Communication ErrorCommunication failure between the user interface and the machine control board.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Viking error codes
Common questions
How do I find the error code on my Viking Dishwasher?
Most Viking dishwashers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Viking dishwashers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.