mypros+
Error code reference

Vision Washer Error Code dr:01

IGBT short circuit

Vision codesVision washer codes

IGBT short circuit – damaged inverter control.

First step from the service manual

Replace inverter.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for dr:01.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What dr:01 means on a Vision washer

The dr:01 error code on a Vision washer indicates an IGBT (Insulated Gate Bipolar Transistor) short circuit within the inverter control board. The IGBT is a power semiconductor device that regulates the variable-frequency drive signal sent to the wash motor. When this transistor fails in a shorted state, the inverter loses its ability to safely control motor speed and current delivery, triggering the fault code to protect the system from further damage.

IGBT short circuit faults are typically caused by internal transistor breakdown due to thermal stress, voltage spikes, or sustained overload conditions. When the IGBT shorts, it can allow uncontrolled current to flow through the motor drive circuit, which is a serious electrical fault. The inverter control module houses this transistor and the supporting drive circuitry, meaning the entire inverter assembly is compromised when this fault appears.

Because the IGBT failure represents a damaged inverter control, the corrective action is direct replacement of the inverter board. There is no field-level repair for a shorted IGBT on this integrated assembly. Attempting to run the washer with an active dr:01 fault risks damage to the motor windings and other connected components downstream of the inverter output.

Source: manufacturer service documentation.

Common causes of dr:01

  1. 01

    Failed IGBT transistor on inverter board

    Part replacement

    The IGBT power transistor on the inverter control has shorted internally, which is the direct cause of this fault. This is confirmed by the error code definition and requires inverter board replacement.

  2. 02

    Thermal overload of inverter components

    Part replacement

    Excessive heat buildup inside the control compartment can degrade and eventually short the IGBT. Check for blocked ventilation around the control board area and signs of heat discoloration on the board.

  3. 03

    Voltage spike or power surge damage

    Part replacement

    A sudden surge in incoming line voltage can exceed the IGBT's rated breakdown voltage and cause an immediate short-circuit failure. Inspect the power supply connection and consider surge protection for the outlet.

  4. 04

    Motor winding short causing inverter overload

    Wiring / connection

    A shorted motor winding can force excessive current back through the inverter, stressing the IGBT to the point of failure. Before installing a new inverter, verify the motor windings are intact to avoid repeat failures.

See the test procedure for each cause

Frequently asked questions about dr:01

What does dr:01 mean on a Vision washer?
The dr:01 code on a Vision washer indicates an IGBT short circuit within the inverter control board. The IGBT is a power transistor that controls motor speed and current. When it fails in a shorted state, the washer shuts down to prevent further electrical damage. The inverter control board must be replaced to resolve this fault.
Can I fix the dr:01 error myself, or do I need a technician?
The dr:01 fault requires replacing the inverter control board, which involves working with high-voltage components. This repair is best handled by a qualified appliance technician. A knowledgeable DIYer comfortable with appliance electronics can perform the replacement, but the inverter board handles line voltage and motor drive currents that present a serious shock hazard if mishandled.
Is it safe to use my Vision washer when dr:01 is displayed?
No, you should not attempt to run the washer while the dr:01 fault is active. A shorted IGBT represents a serious electrical fault that can cause damage to the motor and other downstream components. The washer's control system has shut down for this reason, and continuing to operate it risks making the repair more extensive and costly.
Will resetting my Vision washer clear the dr:01 error code?
Resetting the washer by unplugging it will not clear the dr:01 fault permanently because the underlying hardware failure in the inverter board still exists. The code will return as soon as the machine attempts to operate the motor. A reset may temporarily clear the display, but the shorted IGBT must be addressed by replacing the inverter before the washer can function normally.
How much does it cost to repair a Vision washer with a dr:01 error?
The total repair cost depends on the price of the replacement inverter control board and any applicable labor charges. Parts and labor combined typically range from $150 to $350, depending on part availability and your location. Before ordering a replacement inverter, it is worth checking the motor windings for faults to avoid a repeat failure after the repair.

Related Vision washer codes

All Vision washer codes
View all 34 Vision washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass