mypros+
Model reference

Vision WFFVVC

Washer

1 document35 error codes12 service modes

Available documentation

Service Manual

  • Wffvvc Vision 16 Washer Repair Instruction42 pg
    Covers this model
MyPros+ Max

Diagnose your Vision WFFVVC.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (35)

CodeMeaning
dr:01IGBT short circuitdr:02IGBT interruptiondr:06NTC-relay failuredr:08Speedometer failuredr:09Line over voltage error (short)dr:10Power limiter switch offdr:11Voltage too lowdr:15Power limiter warningdr:19Motor asymmetry errordr:20IGBT power stage short circuitdr:21Line over voltage error (long)dr:22IGBT temperature sensor errordr:23Over temperature of heat sinkdr:24Line frequency rangedr:25A/D converter errordr:26Temperature warning.dr:27DC voltage warning.dr:28Speed follow warning.Er:01Door openEr:04Door actuation defectiveEr:05NTC interruptionEr:06NTC short circuitEr:07Unexpected heating (temperature increase without actuation of heater)Er:08Heating time exceeded (heater does not switch off)Er:09Heater relay stuck.Er:11No communication between control and inverterEr:12Water inlet time exceededEr:13Pumping time exceededEr:14Safety level reachedEr:17Aquastop error
View all 35 error codes
Er:20Spin cycle terminatedEr:21Foam detected.Er:22Frequency synchronisation failure between control mainEr:24Power supply relay to inverter damagedEr:25Door lock blocked

Service modes (12)

  • P:01 - Error display["Enter test program mode.","Scroll to P:01 using MENU button.","Press START/PAUSE to view last…
  • P:02 - Safety test["Enter test program mode.","Scroll to P:02 using MENU button.","Press START/PAUSE to start."]
  • P:03 - Automatic test sequence["Enter test program mode.","Scroll to P:03 using MENU button.","Press START/PAUSE to start."]
  • P:04 - Motor test["Enter test program mode.","Scroll to P:04 using MENU button.","Press START/PAUSE to start."]
  • P:06 - Display test["Enter test program mode.","Scroll to P:06 using MENU button.","Press START/PAUSE to start."]
  • P:07 - Buttons and selector switch test["Enter test program mode.","Scroll to P:07 using MENU button.","Press START/PAUSE to start."]
  • P:13 - Valves test["Enter test program mode.","Scroll to P:13 using MENU button.","Press START/PAUSE to start."]
  • P:14 - Buzzer test["Enter test program mode.","Scroll to P:14 using MENU button.","Press START/PAUSE to start."]
  • P:15 - Pump test["Enter test program mode.","Scroll to P:15 using MENU button.","Press START/PAUSE to start."]
  • P:16 - Heater test["Enter test program mode.","Scroll to P:16 using MENU button.","Press START/PAUSE to start."]
  • P:17 - Noise test["Enter test program mode.","Scroll to P:17 using MENU button.","Press START/PAUSE to start."]
  • Test program (diagnostic mode)["Set program selector switch to OFF position.","Press and hold MENU + SELECT buttons for at least…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Vision washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass