mypros+
Error code reference

Whirlpool Dishwasher Error Code F6E9

Water tank valve not functioning; loose connection in valve circuit and/or open water valve solenoid.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F6E9 error code actually means

Your Whirlpool dishwasher has detected a problem with the valve that controls the water reuse system, meaning it cannot confirm the valve is working correctly. This is usually caused by a broken electrical component inside the valve or a loose wire connection leading to it. The dishwasher has stopped operating to alert you that this part of the system needs to be inspected.

Diagnostic procedure

The full F6E9 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Unplug dishwasher or disconnect power and check resistances of water reuse valve solenoid and all connections in the Water Reuse Valve circuit with meter. Fix/replace open connection/part.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F6E9 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F6E9

Ranked by how often they cause this code
  1. 1Open water reuse valve solenoid
  2. 2Loose or disconnected wiring connector
  3. 3Corroded or damaged wire terminals
  4. 4Broken or chafed wiring in the valve circuit
  5. 5Faulty control board output

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F6E9

What does F6E9 mean on a Whirlpool dishwasher?
F6E9 means the dishwasher has detected that the water tank valve, specifically the water reuse valve, is not functioning correctly. The fault points to either an open solenoid coil inside the valve or a loose, broken, or corroded connection somewhere in the valve circuit wiring. The dishwasher stops operating and displays this code to alert you that the valve circuit needs electrical testing and repair.
Is it safe to use my Whirlpool dishwasher while F6E9 is displayed?
It is not recommended to continue running the dishwasher while F6E9 is active. The error indicates the water reuse valve circuit is not functioning properly, which means the appliance may not manage water correctly during a cycle. Continuing to run cycles without addressing the fault could lead to incomplete cleaning or additional system issues.
How much does it cost to repair a Whirlpool dishwasher showing F6E9?
Repair costs vary depending on the root cause. If only a loose connector needs to be reseated, there may be no parts cost, though a service call from a technician typically runs in the range of $75 to $150. Replacing the water reuse valve solenoid or valve assembly generally adds parts costs in the range of $30 to $100 or more depending on the specific model. If a wiring harness or control board is involved, total repair costs can be higher.
How do I fix the F6E9 error code on my Whirlpool dishwasher?
Start by unplugging the dishwasher or shutting off its circuit breaker before doing anything else. Use a multimeter to measure the resistance of the water reuse valve solenoid and check continuity through all connectors and wiring in the valve circuit. If the solenoid reads open or a connector is found loose or damaged, repair or replace the faulty component. Restore power after repairs to confirm the error has cleared.
Will resetting my Whirlpool dishwasher clear the F6E9 error code?
A reset may temporarily clear the F6E9 code from the display, but the error will return if the underlying fault in the water reuse valve circuit has not been repaired. Resetting is useful for confirming whether the fault is persistent or intermittent, but it is not a substitute for testing and fixing the solenoid or wiring. Address the electrical fault to prevent the code from recurring.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass