mypros+
Error code reference

Whirlpool Washer Error Code DOOR SWITCH ERROR

The door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the DOOR SWITCH ERROR error code actually means

Your washer has detected a problem with the door switch, either because the door has not been opened between wash cycles or because the switch is not communicating correctly with the washer's control board. This usually means the door latch or switch needs to be inspected or replaced. Try opening and closing the door firmly, then starting a new cycle to see if the error clears.

Diagnostic procedure

The full DOOR SWITCH ERROR procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Open and close the door, then verify CCU operation by running a Diagnostic Test or any cycle.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock DOOR SWITCH ERROR procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of DOOR SWITCH ERROR

Ranked by how often they cause this code
  1. 1Faulty Door Switch
  2. 2Door Not Opened Between Cycles
  3. 3Damaged or Corroded Wiring Harness
  4. 4Worn or Damaged Door Latch Assembly
  5. 5CCU Malfunction

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about DOOR SWITCH ERROR

What does DOOR SWITCH ERROR mean on a Whirlpool washer?
The DOOR SWITCH ERROR means the washer's control board has detected a problem with the door switch circuit. This happens in one of two ways: the door was not opened for 3 consecutive cycles, or the door switch read as open while the door was locked for more than 5 seconds. The error indicates a sensing or communication issue between the door switch and the Central Control Unit.
Will resetting the washer clear the DOOR SWITCH ERROR?
Opening the door and running a new cycle or Diagnostic Test is the recommended first step and can clear the error if the root cause was simply that the door had not been opened for 3 consecutive cycles. However, if the door switch itself is faulty or the wiring is damaged, the error will return until the underlying problem is repaired.
How much does it cost to fix a DOOR SWITCH ERROR on a Whirlpool washer?
Repair costs vary depending on the failed component. A replacement door switch or latch assembly typically costs between $15 and $75 for the part alone. If a technician performs the repair, total costs including labor generally range from $100 to $250. CCU replacement, if required, is the most expensive scenario and can run $200 to $400 or more.
Can I fix the DOOR SWITCH ERROR myself?
In many cases, yes. Start by opening and closing the door firmly, then run a Diagnostic Test or a regular cycle to see if the error clears. If the error persists, check the door latch assembly and the wiring harness for visible damage or loose connectors. Replacing a faulty door switch is a repair many experienced DIYers can complete with basic tools.
Is it safe to use my washer when the DOOR SWITCH ERROR is displayed?
You should not continue running the washer while this error is active. The door switch is a safety component that confirms the door is properly locked before and during a cycle. If the switch is not functioning correctly, the washer may not be able to verify that the door is secure, which creates a safety risk.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass