Model reference

Amana VBC-35CT-1J/P54878-10C

Name: Amana VBC-35CT-1J/P54878-10C
Brand: Amana

Air Conditioner

4 documents22 error codes15 service modes

Available documentation

Tech Sheet

tech sheet 1207421228 pg
Covers this model
tech sheet w10338674 reva44 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model

Installation Guide

Installation Instructions21 pg
Covers this model

MyPros+ Max

Diagnose your Amana VBC-35CT-1J/P54878-10C.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Air Conditioner

F0E0 on my Amana VBC-35CT-1J/P54878-10C

M+

No fault codes stored in memory.

From Tech Sheet W14675985, p.37:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (22)

CodeMeaning

F0E0No fault codes stored in memory.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (water temperature 40.5°C /…F0E5Off balance load detected during operation.F1E1Main control fault detected.F1E2Motor control fault; fault of the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and user interface; the UI identification does not…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open, or main…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (15)

Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
Electronic Testing Mode - Forced Compressor Start["Press Display On pad to activate control panel","Simultaneously press and hold Max Frz pad and…
Electronic Testing Mode - Forced Defrost Start["Press Display On pad to activate control panel","Simultaneously press and hold Max Ref and…
Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
Program Mode A (Thermistor Temperature Reading)["Open refrigerator door","Press Display On pad","Press Vacation pad","Within 6 seconds press the…
Program Mode B - Forced Defrost["Enter Program Mode B","Press and hold Alarm Off pad for 3 seconds"]
Program Mode B - Forced Pulldown (Compressor Start)["Enter Program Mode B","Press and hold Max Frz pad for 3 seconds"]
Program Mode B (Service Programming)["Enter Program Mode A first (see Program Mode A entry sequence)","Toggle to Program Mode B by…
Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass