Model reference
Amana GHE105DM-3/P96524-7F
Furnace
6 documents19 error codes17 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10097033 - Rev A16 pg
- Tech Sheet - W10238799 - Rev A16 pg
- Tech Sheet - W11087920 - Rev A60 pg
- Tech Sheet - W10403269 - Rev A52 pg
Tech Tip
- Instruction Sheet4 pg
Quick Reference
- Quick Reference Manual4 pg
MyPros+ Max
Diagnose your Amana GHE105DM-3/P96524-7F.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (19)
CodeMeaning
F1E1Primary control failure indicating the machine control electronics has failed.F2E1Stuck button or user interface mismatch; only appears in service diagnostic…F2E2User Interface software errorF3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<20 ohms).F3E5Inlet and exhaust thermistors are open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; only appears in service diagnostic…F4E3Restricted/low air flow that may affect dryer performance.F4E4Low line voltage detected.F6E1ACU and HMI have not communicated for a specified amount of time.F6E2WiFi Module has not responded for a specified amount of time.F8E1No voltage is detected at the water valve relayFCE1WiFi Module communications lost.L2Low L2 voltage (less than 50V) detected at installation.PFA power failure occurred while the dryer was running.Service modes (17)
- Actuator and Switch Test["Set TEMP SELECT switch to Hot/Cold (HC).","Unplug the washer power cord from the household outlet…
- Automatic Operations Test["Set TEMP SELECT switch to Cold/Cold (CC).","Unplug the washer power cord from the household…
- Component Activation / Quick Service Cycle (LCD in Door Models)["Enter Service Diagnostic Mode (LCD in Door) first.","From the DIAGNOSTICS HOME screen, scroll…
- Customer-Focused Drying Mode Adjustment["Ensure the dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
- Customer-Focused Dryness Level Adjustment1
- Install Diagnostics1
- Interface Test["Set TEMP SELECT switch to Warm/Warm (WW).","Unplug the washer power cord from the household…
- Key Activation & Encoder Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- Loads Test Mode1. Dryer must be in standby mode (plugged in with all indicators off). 2. Within 5 seconds: press…
- Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
- Service Diagnostic Mode (Console Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
- Service Diagnostic Mode (LCD in Door Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Open and close the…
- Service Test Mode (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- Software Version Display1
- Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
- User Interface Test1
- User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana furnace models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass