mypros+
Model reference

Amana OC-100-3/P96235-2F

Furnace

3 documents30 error codes22 service modes

Available documentation

Tech Sheet

  • Whirlpool Amana WED9050XW NED7300WW1 Electric Dryer Tech Sheet Tech Sheet W1023879512 pg
    Covers this model
  • Tech Sheet - 820512424 pg
    Covers this model

Installation Guide

  • Installation Instructions60 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OC-100-3/P96235-2F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (30)

CodeMeaning
:Flashing colon indicates a power failure has occurred.F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (water temperature 40.5°C /…F0E5Off balance load detected during cycle.F1E1Primary control failure.F1E2Motor control fault of the motor control section of the main control.F2Membrane switch (touch panel) failure.F2E1Stuck button or user interface mismatchF2E3Mismatch of main control and user interface; the UI identification does not…F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E4Low line voltage detected.F5E1Lid switch fault; lid is in locked state but lid switch is open, or main…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F6Microwave relay failure.F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold water inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after the drain pump is on for 10…PFPower failure occurred while the dryer was running.

Service modes (22)

  • Calibration Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Rinse' LED is…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'In Use', 'Soak/Wash'…
  • Customer-Focused Drying Mode Adjustment["Ensure the dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
  • Diagnostic Mode (LCD models)["Enter service mode first","Rotate timer dial through positions to access different diagnostic…
  • Drain & Spin Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Done' LEDs…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until only the 'Done' LED…
  • Idle/Service Mode (MAH5500B/MAH6500)["With washer in Off position, press and hold the Fabric Selection button and the Options…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Final Spin' and 'Done'…
  • Motor and Motor Control Test["1
  • Motor and Motor Control Test (Delay Mode Test)["Set the timer knob into the delay increments.","Press the push-to-start switch to start the…
  • Motor Phase Test["1
  • Quick Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Final Spin' LED…
  • Quick Service Test (MAH5500/MAH6500 - LCD models)["1. Turn cycle selector knob to a position.","2. Press and hold the Start/Stop button.","3. The…
  • Quick Spin Test (LCD models)["Enter service mode","Set timer to appropriate position for spin test","Washer will execute spin…
  • Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Service Mode (MAH5500/MAH6500 - LCD models)["Set timer to any Off position","Press and hold the Fabric Selection and Options buttons…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse', 'Final Spin'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Soak/Wash' and 'Done'…
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["1
  • UI (Rotary Switch) Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Final Spin'…
  • User Interface/Control System Test["First activate the Service Diagnostic Mode.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass