mypros+
Model reference

Amana OH-85-3/P96236-2F

Furnace

7 documents26 error codes22 service modes

Available documentation

Service Flash

  • Service Update First HALF—200994 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
  • Installation Instructions20 pg
    Covers this model
  • Installation Instructions7 pg
    Covers this model
  • Installation Instructions16 pg
    Covers this model
  • Installation Instructions20 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OH-85-3/P96236-2F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (26)

CodeMeaning
F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E4High water temperature detected (40.5°C / 105°F or higher) during the rinse…F0E5Off balance load detected during operation.F1E1Main control fault detected.F1E2Motor control fault on the motor control section of the main control.F2Touch panel failure.F2E1Stuck button detected; the START button has been actuated for 10 consecutive…F2E3Mismatch of main control and user interface; the UI identification does not…F3E1Pressure sensor fault; the main control detects an out of range pressure signal.F3E2Inlet water temperature fault; the inlet thermistor is detected to be open or…F3HHumidity sensor failure.F5E1Lid switch fault; lid is in locked state but lid switch is open, or the main…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F6Microwave relay failure (relay 4903).F7E1Basket speed sensor fault; the main control cannot determine speed of basket or…F7E5Shifter fault; the main control cannot determine the position of the shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; the water level does not change for a period of time or water is…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F8E6No fill; the water level does not change for a period of time or water is…F9E1Long drain; the water level does not change after the drain pump has been on…PFPower failure indication; blinks in the display after a power outage longer…

Service modes (22)

  • Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Calibration Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Control Lock["Ensure the microwave oven and Timer are off.","Touch and hold OFF for 5 seconds until two tones…
  • Demo Mode["Ensure the microwave oven and Timer are off.","Touch and hold Timer for 5 seconds until two tones…
  • Diagnostic Mode (LCD models)["Enter service mode first","Rotate timer dial through positions to access different diagnostic…
  • Drain & Spin Cycle["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Fault Code Display Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Idle/Service Mode (MAH5500B/MAH6500)["With washer in Off position, press and hold the Fabric Selection button and the Options…
  • Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Manual Overview Test Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Motor and Motor Control Test["1
  • Motor and Motor Control Test (Delay Mode Test)["Set the timer knob into the delay increments.","Press the push-to-start switch to start the…
  • Motor Phase Test["1
  • Quick Overview Test Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Quick Service Test (MAH5500/MAH6500 - LCD models)["1. Turn cycle selector knob to a position.","2. Press and hold the Start/Stop button.","3. The…
  • Quick Spin Test (LCD models)["Enter service mode","Set timer to appropriate position for spin test","Washer will execute spin…
  • Service Mode (MAH5500/MAH6500 - LCD models)["Set timer to any Off position","Press and hold the Fabric Selection and Options buttons…
  • Software Version Display Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Tachometer Verification Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…
  • Touch Panel and Electronic Control Self-Diagnostic Test["Press and hold CANCEL/OFF while opening the door.","While still holding the CANCEL/OFF button…
  • Touch Panel and Electronic Control Test (Self-Diagnostic)["Press and hold CANCEL/OFF while opening the door.","While still holding the CANCEL/OFF button…
  • UI (Rotary Switch) Test Mode["Ensure washer is in standby mode (plugged in, all indicators off).","Place cycle selector knob…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass