mypros+
Model reference

Amana RC-10B-DD/P73547-6M

Microwave

5 documents62 error codes22 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W1037157520 pg
    Covers this model
  • Tech Sheet - W10419696 - Rev A28 pg
    Covers this model
  • Tech Sheet - W11467195 - Rev B24 pg
    Covers this model
  • Commercial Microwave Technical Information10 pg
    Covers this model
  • Tech Sheet16 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RC-10B-DD/P73547-6M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (62)

CodeMeaning
:Flashing colon indicates a power failure has occurred.AFLow airflow detected that may affect dryer performance.F0 E7Low Voltage ErrorF1 E1ACU (Appliance Control Unit) fault detected.F1 E4UIC (User Interface Control) fault detected.F1 E6Voltage input fault detected.F1 E7Voltage input fault detected.F1.E1Relay Control Board defective.F1E1Motor relay stuck on, indicates an ACU problem.F1E3Incorrect controller installed (electric models only); ACU or UI part number…F1E5ACU parameter file missing; parameter memory invalid.F2Touch panel failure.F2 E1Dryer keypad stuck errorF2 E2Upper Dryer Keypad Stuck ErrorF2.H1Hood/light switch stuck.F2.H2Hood/light switch error.F2.Q1User interface board (UIB) is not reading keypad inputs.F2E1Stuck button on User Interface (depressed for over 20 seconds); only appears in…F2E3UI and ACU model ID parameter mismatch caused by replacement of either the UI…F2E4UI software errorF2E5UI software errorF3 E1Thermistor faultF3.H1Humidity sensor failure.F3.T1UIB (user interface board) thermistor failure.F3.T2FC (forced convection) thermistor failure.F3.T4Magnetron thermistor failure.F3E1Exhaust thermistor open or shorted; open if temperature drops below 18°F (>50k…F3E2Moisture sensor strip is open or shorted; only appears in service diagnostic…F3E3Inlet thermistor is open (>245k ohms, below 18°F) or shorted (<328 ohms, above…F3E7Rear moisture sensor strip is open or shorted (Maytag models only); only…
View all 62 error codes
F3HHumidity sensor failure.F4E1Heater 1 failure or connector problem; no voltage detected at the heater relay.F4E2No voltage detected at heater relay 2; heater 2 failure or connector problem…F4E3Restricted airflow; low airflow that may affect dryer performance.F4E4L2 line voltage error (electric models only); low L2 voltage (less than 50V)…F4E5High limitF5 E1Dryer door circuit error.F5 E6Upper Dryer Door Circuit ErrorF6MW relay failure (Relay 4903 on Relay Board).F6 E1Communication failure between ACU and UICF6E2Communication errorF6E3Communication errorF7Power to magnetron interrupted.F7 E6Lower Dryer Motor Circuit ErrorF7 E7Upper Dryer Motor Circuit ErrorF7 E8Lower Dryer Motor Sense ErrorF7 E9Upper Dryer Motor Sense ErrorF9Relay Control Board communications error.F9.QTouch communication error.FC E1Model/Serial number not programmed.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.L2Low L2 voltage (less than 30V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (22)

  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS or DRY LEVEL…
  • Diagnostic Mode["Enter Setup Mode first.","Press DELICATES keypad for one second while in any of the set-up codes…
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • diagnostic_modePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Fault Code Display / ClearFrom Service Diagnostic Mode
  • Help Mode["Enter Setup Mode first.","Navigate to set-up option 2.XX (or while dAS displays if operating with…
  • help_modePress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • model_serial_number_menuEnter Help Mode first
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Setup Mode["COIN Models
  • Setup Mode (Control Set-Up)["PD Models
  • setup_modeCOIN Models
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • Test Mode (Touch Panel and Relay Control Board Tests)["1
  • Touch Panel and PCBA Self-Diagnostic Test Mode["1
  • Touch Panel Test Mode["1
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • usb_menuEnter Help Mode first
  • wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass