Model reference

Amana RC-10D/P71305-2M

Name: Amana RC-10D/P71305-2M
Brand: Amana

Microwave

3 documents58 error codes27 service modes

Available documentation

Tech Sheet

Tech Sheet20 pg
Covers this model
Tech Sheet - W11467195 - Rev B24 pg
Covers this model
techsheet-w10420006-reva_W1042000656 pg
Covers this model

MyPros+ Max

Diagnose your Amana RC-10D/P71305-2M.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Microwave

AF on my Amana RC-10D/P71305-2M

M+

Restricted/low air flow detected that

From Tech Sheet W12069863, p.35:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (58)

CodeMeaning

AFRestricted/low air flow detected that may affect dryer performance.E0No errors, functioning ice maker.E1No cooling; ice maker timed out because ice compartment was unable to reach…E2Motor lost position; ice maker did not find home during harvest and exceeded…E3Heater time-out; ice mold heater was ON longer than maximum allowable time E4Dry cycle; unit detected dry cycles above minimum requirement E5IM bad thermistor; ice storage temperature satisfied but ice mold in frozen…E6Manufacturing code ErManufacturing code F0 E7Control board recognized line voltage below 90 VAC.f1 e1Primary control failure.F1 E4UIC (User Interface Control) fault detected.F1 E6Voltage input fault detected.F1 E7Voltage input fault detected.F1E1Indicates a Cycle Control Unit (CCU) problem.F1E4Microwave ACU PCBA failure.f2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2 E2Upper dryer keypad is sensed pressed for 60 seconds (stuck key).F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2UI software error; UI cannot read EEPROM software.f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open

View all 58 error codes

F3E7Moisture sensor strip has shorted F4E1No voltage detected at the heater relay F4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5 E1Dryer door circuit error.F5 E6Upper dryer door circuit error.F6 E1Communication failure between ACU and UIC F6E1Communication between the CCU and UI has not been detected (UI to CCU).F6E2Communication between the CCU and UI has not been detected (CCU to UI).F7 E6Lower dryer motor circuit error.F7 E7Upper dryer motor circuit error.F7 E8Lower dryer motor sense error F7 E9Upper dryer motor sense error f8 e1No voltage detected at the water valve relay (steam models only, only appears…F8E5Exhaust air temperature detection failure.FC E1Model/Serial number not programmed.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failure FC E6Model setup export failure FC E7Model setup import failure FC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.L2Low L2 voltage (less than 50V) detected at the CCU.pfPower failure occurred while the dryer was running.

Service modes (27)

Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
Customer-Focused Drying Mode Adjustment1
Customer-Focused Dryness Level Adjustment1. Turn cycle selector knob to an automatic cycle. 2. From the Automatic Cycle Main Screen, press…
diagnosticPress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
Diagnostic Mode["Enter Setup Mode first.","While in any of the set-up codes 1 through 6 (or while dAS displays if…
Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press CANCEL to enter Standby mode (colon ':'…
diagnostic_modePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
helpPress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
Help Mode["Enter Setup Mode first.","While in special pricing option step 2.XX (or while dAS displays if…
help_modePress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
model_serial_number_menuEnter Help Mode first
Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
Quick Diagnostic TestFrom Diagnostics Home screen, select 'Error Diagnostic', then select 'Quick Diagnostic Test'
Service Diagnostic Mode1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only DONE/COMPLETE…
Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
Service Diagnostics ModePress SW1 and SW2 simultaneously for 3 seconds
setupPD Models
Setup Mode["Stacked PD Models
Setup Mode (Control Set-Up)["PD Models
setup_modeCOIN Models
UI Component TestFrom Diagnostics Home screen, select 'Component Activation', then select 'UI Component Test'
USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
usb_menuEnter Help Mode first
User Interface/Control System TestAfter activating Service Diagnostic Mode, press and release the 1st button used to activate Service…
wi-fi_menuFrom the F0 screen in setup mode, press HEAVY DUTY keypad to enter Wi-Fi mode
wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass