mypros+
Model reference

Amana RR-5B

Microwave

7 documents83 error codes15 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 97629906 pg
    Covers this model
  • Tech Sheet - W10117605A6 pg
    Covers this model
  • Tech Sheet - W10115596A6 pg
    Covers this model
  • Tech Sheet - W10135713A6 pg
    Covers this model
  • Tech Sheet - W10200950 - Rev A8 pg
    Covers this model
  • tech sheet w11266092 revA16 pg
    Covers this model

Service Manual

  • TECHNICAL MANUAL JennAir® and KitchenAid® Under-Counter Microwave Oven with Drawer55 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RR-5B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (83)

CodeMeaning
1-1Control detected K1 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…10-1Dispenser electrical problem2-1Control detected stuck key(s) in keypad or keypad connection.3-1Open connector or component in Temperature Sensing circuit, open or faulty…3-2Incoming water temperature above 167°F (75°C), shorted connection or component…3-3OWI calibration failure or drain hose check valve not sealing allowing dirty…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open5-2Door stuck closed6-1Low or no water due to mechanical problem6-2Fill valve electrical problem6-3Suds or air detected in pump6-4Float switch open7-1No heat7-2Heater stuck on8-2Drain motor electrical problem8-3Drain stuck onCLrNo error(s) found; no corrective action required.E0EEPROM communications error.E0 F1EEPROM checksum failure.E0 F2Shorted key detected.E0 F3Oven sensor opened.E0 F5Door and switches do not agree.E0-F1EEPROM checksum error.E0-F2Shorted key detected.E0-F3Oven sensor opened.E0-F5Door and switches do not agree.E1Door latch does not function properly.E1 F1UL A/D error(s).
View all 83 error codes
E1 F2Shorted key detected.E1 F3Oven sensor shorted.E1 F5Door latch not operating.E1-F1UL A/D errors.E1-F3Oven sensor shorted.E1-F5Door latch not operating.E2Latch error during self-clean operation.E2 F1EEPROM communications failure.E2 F2Shorted key detected.E2 F3BAKE/BROIL range over temperature.E2 F5Latch error during CLEAN.E2-F1EEPROM communication error.E2-F3BAKE/BROIL range over temperature.E2-F5Latch error during CLEAN.E3 F3CLEAN range over temperature.E3-F3CLEAN range over temperature.ERRORHumidity sensor (AH sensor) cannot balance the bridge circuit due to…F1Control failureF1-E0EEPROM checksum failure.F1-E1UL A/D error(s).F1-E2UL A/D error(s).F1E1Indicates a CCU (Cycle Control Unit) problem.F2Shorted key detected on control panel.F2-E0Shorted key detected.F2-E1EEPROM communications error.F2-E2BAKE/BROIL range over temperature condition.F2-E3CLEAN range over temperature condition.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F2E2User Interface software errorF3Oven sensor opened or oven sensor shorted.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; this fault code appears ONLY when in…F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5Door and door switches do not agree (mismatch between door position and switch…F5-E0Door and switches do not agree.F5-E1Door latch not operating.F5-E2Latch error during CLEAN.F6E1Communication error from UI to CCU; communication between the CCU and UI has…F6E2Communication error from CCU to UI; communication between the CCU and UI has…GoodNo fault detected, normal operation.L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (15)

  • AH Sensor Diagnostic Test (Water Load Cooking Test)["Ensure oven has been plugged in at least 2 minutes before testing.","Fill approximately 200 ml…
  • BAKE Temperature AdjustmentPress and hold BAKE key for 5 seconds
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Diagnostic ModeWith the oven not in bake, broil, or clean mode, press Cancel/OFF, then Cancel/OFF, then START in…
  • Diagnostics ModeWith the oven not in cooking, broiling or cleaning mode, press Cancel/OFF, Cancel/OFF, START. The…
  • Fault Code Display and Clear["Activate Service Diagnostic Mode first.","Press and release the 3rd button to display saved fault…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Diagnostics Cycle1. With dishwasher in standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • Temperature AdjustmentPress and hold BAKE key for 5 seconds
  • Temperature Adjustment ModePress and hold BAKE key for 5 seconds
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass