mypros+
Model reference

Caloric DCR-211-1L-OM

Dishwasher

44 error codes16 service modes
MyPros+ Max

Diagnose your Caloric DCR-211-1L-OM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (44)

CodeMeaning
E2Overheating of the induction coil (display flashing).E5Error on filter board due to incorrect wiring or error on power board.E6Error on power unit due to incorrect wiring or error on power board.E9Coil temperature sensor defective.Er 20Flash failure; microcontroller (μC) is faulty.Er 22Permanent use of keypads; control unit cuts off after 10 seconds due to water…Er 31Configuration data incorrect; configuration of induction necessary.Er 36NTC value is not within its specification (value < 200 mV or > 4.9 V); control…Er 47Communication error between touch control (TC) and induction module; none or…F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during the rinse cycle.F0E5Off balance load detected during operation.F1E1Indicates a CCU (Cycle Control Unit) problem.F1E2Motor control fault; fault of the motor control section of the main control.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; this…F2E2UI cannot read EEPROM software from the User Interface.F2E3Switch mismatch; switches do not match the console or are not operating…F3E1Exhaust thermistor is open; temperature drops below 18°F (> 50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (< 500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (> 245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (< 328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if the P14 connector is…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Moisture sensor strip has shorted; this fault code will ONLY appear when in the…F4E1No voltage detected at the heater relay; appears ONLY when in the Diagnostic…F4E3Restricted air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5E1Lid switch fault; lid is in locked state but lid switch is open, control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…
View all 44 error codes
F5E4Lid not opened between cycles; user presses START after several consecutive…F6E1Communication between the CCU and UI has not been detected (UI to CCU…F6E2Communication between the CCU and UI has not been detected (CCU to UI…F7E1Basket speed fault; main control cannot determine speed of basket or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.U400Secondary voltage of the power unit too high (primary > 300 V); control unit…

Service modes (16)

  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' LED is ON…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Rinse' LED is ON…
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Diagnostic Test Mode1
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Done' LED is ON…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' and 'Done'…
  • Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Wait 10 seconds after…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Rinse', 'Spin', and…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Wash' and 'Done'…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Rinse' and 'Spin'…
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax